采用金相显微镜、扫描电镜、透射电镜、X射线衍射仪、拉伸试验机、硬度计等研究了4343/3003/4343铝合金轧制复合板在100~500℃退火15min~10h后的微观组织和力学性能.结果表明:芯层合金300℃退火1h后开始再结晶,370℃以上退火1h后已完全再结晶且伴随有弥散相析出,弥散相析出后通过钉扎晶界阻碍再结晶晶粒长大;1h退火时,随退火温度升高,芯层合金晶粒先增大后减小,复合板的拉伸强度与硬度先降低后升高;370℃退火时,随退火时间延长,芯层合金再结晶程度增加,晶粒缓慢长大,复合板的拉伸强度与硬度下降;复合板最佳退火工艺为370℃/1h.
参考文献
[1] | 刘禹,王祝堂.汽车热交换铝材概览[J].轻合金加工技术,2011(05):1-16,20. |
[2] | 王祝堂.汽车热交换器用铝板带箔[J].轻合金加工技术,2005(11):1-8,51. |
[3] | 祖国胤,李兵,李鸿,于九明.冷轧复合对铝合金复合箔组织与性能的影响[J].东北大学学报(自然科学版),2008(05):689-692. |
[4] | 王宁,Jarl Erik FLAT(Φ)Y,李彦军,Knut MARTHINSEN.AlMnFeSi合金退火过程中的微观组织及力学性能的演变[J].中国有色金属学报(英文版),2012(08):1878-1883. |
[5] | 张新明,张静,唐建国,周德敬,尹林.中间退火对4343/3003/7072汽车热交换器用铝合金复合箔抗下垂性能的影响[J].中南大学学报(自然科学版),2012(01):59-65. |
[6] | EIZADJOU M;MANESH D H;JANGHORBAN K .Investigation of roll bonding between aluminum alloy stripes[J].Materials and Design,2008,585(29):900-913. |
[7] | 王冠,李远波,郭钟宁,张永俊.汽车散热器新型铝合金钎焊接头腐蚀行为的分析[J].焊接学报,2011(06):25-28. |
[8] | HUMPHREYS F J .A unified theory of recovery,recrystallization and grain growth,based on the stability and growth of cellular microstructures-Ⅰ.The basic model[J].Acta Materialia,1997,45(10):4231-4240. |
[9] | HUMPHREYS F J .A unified theory of recovery,recrystallization and grain growth,based on the stability and growth of cellular microstructures-Ⅱ.The effect of second-phase particles[J].Acta Materialia,1997,45(12):5031-5039. |
[10] | JIANTAO LIU;S.W. BANOVIC;R.J. FIELDS .Effect of Intermediate Heat Treatment on Microstructure and Texture Evolution of Continuous Cast Al-Mn-Mg Alloy Sheet[J].Metallurgical and Materials Transactions, A. Physical Metallurgy and Materials Science,2006(6):1887-1898. |
[11] | ROBSON J D;HENRY D T;DAVIS B .Particle effect on recrystallization in magnesium-manganese alloys:particle-stimulated nucleation[J].Acta Materialia,2009,57(9):2739-2747. |
[12] | Song XY;Rettenmayr M .Modeling recrystallization in a material containing fine and coarse particles[J].Computational Materials Science,2007(2):234-245. |
[13] | HUMPHREYS F J;HATHERLY M.Recrystallization and Related Annealing Phenomena[M].Oxford:Elsevier Science Ltd,1995:393-415. |
[14] | Robson, J.D.;Henry, D.T.;Davis, B. .Particle effects on recrystallization in magnesium-manganese alloys: Particle pinning[J].Materials Science & Engineering, A. Structural Materials: Properties, Misrostructure and Processing,2011(12):4239-4247. |
[15] | L. P. Troeger;E. A. Starke Jr. .Particle-stimulated nucleation of recrystallization for grain-size control and superplasticity in an Al-Mg-Si-Cu alloy[J].Materials Science & Engineering, A. Structural Materials: Properties, Misrostructure and Processing,2000(1/2):19-29. |
[16] | S. TANGEN;K. SJOLSTAD;T. FURU;E. NES .Effect of Concurrent Precipitation on Recrystallization and Evolution of the P-Texture Component in a Commercial Al-Mn Alloy[J].Metallurgical and Materials Transactions, A. Physical Metallurgy and Materials Science,2010(11):2970-2983. |
[17] | 张新明,吴文祥,刘胜胆,蹇雄,唐建国.退火过程中AA3003铝合金的析出与再结晶[J].中南大学学报(自然科学版),2006(01):1-5. |
[18] | ALEXANDER D T L;GREER A L .Solid-state intermetallic phase transformation in 3XXX aluminium alloys[J].Acts Materialia,2002,50(10):2571-2583. |
[19] | DEHMAS M;WEISBECKER P;GEANDIER G et al.Experimental study of phase transformation in 3003 aluminium alloys during heating by in situ high energy X-ray synchrotron radiation[J].Journal of Alloys and Compounds,2005,400(1-2):116-124. |
[20] | M. DEHMAS;E. AEBY-GAUTIER;ARCHAMBAULT .Interaction Between Eutectic Intermetallic Particles and Dispersoids in the 3003 Aluminum Alloy During Homogenization Treatments[J].Metallurgical and Materials Transactions, A. Physical Metallurgy and Materials Science,2013(2):1059-1073. |
[21] | BAY N .Mechanisms producing metallic bond in cold welding[J].Welding Journal,1983,62(5):137-142. |
[22] | SOMEKAWA H;WATANABE H;MUKAI T et al.Low temperature diffusion bonding in a superplastic AZ31 magnesium alloy[J].Scripts Materialia,2003,48(9):1249-1254. |
上一张
下一张
上一张
下一张
计量
- 下载量()
- 访问量()
文章评分
- 您的评分:
-
10%
-
20%
-
30%
-
40%
-
50%