采用热压烧结法成功制备SiCp／Cu复合材料。采用溶胶‐凝胶工艺在SiC颗粒表面制备Mo涂层，研究Mo界面阻挡层对复合材料热物理性能的影响。结果表明：过氧钼酸溶胶‐凝胶体系能够在S iC颗粒表面包覆连续性、均匀性较好的MoO3涂层，最佳工艺配比为SiC∶MoO3＝5∶1（质量比）、过氧化氢∶乙醇＝1∶1（体积比），SiC表面丙酮和氢氟酸预清洗处理有利于M oO3涂层的沉积生长。M oO3在540℃第一步氢气还原后转变为M oO2，M oO2在940℃第二步氢气还原后完全转变为Mo ，Mo涂层包覆致密完整。热压烧结SiCp／Cu复合材料微观组织致密均匀，且相比原始SiC颗粒增强的SiCp／Cu ，经溶胶‐凝胶法界面改性处理的SiCp／Cu复合材料热导率明显提高，SiC体积分数约为50％时，SiCp／Cu复合材料热导率达到214．16W · m －1· K －1。
SiCp/Cu composites were successfully fabricated by vacuum hot‐pressing method .Molybde‐num coating w as deposited on the surface of silicon carbide by sol‐gel method .T he effects of the inter‐facial design on thermo‐physical properties of SiCp/Cu composites were studied .The results indicate that :continuous and uniform MoO3 coating can be deposited on the surface of silicon carbide by per‐oxomolybdic acid sol‐gel system ,and the best processing parameters are as follows :SiC∶ MoO3 =5∶1(mass ratio) ,H2 O2 ∶C2 H5 OH=1∶1(volume ratio) ,and surface pretreatment with acetone and hydrofluoric acid is good to the deposition and growth of MoO3 coating .After hydrogen reduction at 540℃ for 90min the MoO3 is changed into MoO2 ,and then hydrogen reduction at 940℃ for 90min the MoO2 is changed into Mo absolutely ,and the Mo coating is continuous and uniform .SiCp/Cu compos‐ites prepared by vacuum hot‐pressing method show a compact and uniform microstructure ,and the thermal conductivity of the composites is increased obviously after the Mo coating interfacial modifica‐tion ,w hich can reach 214 .16W · m -1 · K -1 w hen the volume of silicon carbide is about 50% .
参考文献
| [1] | Th. Schubert;A. Brendel;K. Schmid.Interfacial design of Cu/SiC composites prepared by powder metallurgy for heat sink applications[J].Composites, Part A. Applied science and manufacturing,200712(12):2398-2403. |
| [2] | Wang, C.;Min, G.;Kang, S.-B..Thermal conducting property of SiCp-reinforced copper matrix composites by hot pressing[J].Journal of Composite Materials,201118(18):1849-1852. |
| [3] | Sundberg G;Paul P;Sung CM;Vasilos T.Fabrication of CuSiC metal matrix composites[J].Journal of Materials Science,20062(2):485-504. |
| [4] | Wang ZM.;Wynblatt P..Study of a reaction at the solid Cu/alpha-SiC interface[J].Journal of Materials Science,19985(5):1177-1181. |
| [5] | Schubert T;Trindade B;Weissgarber T;Kieback B.Interfacial design of Cu-based composites prepared by powder metallurgy for heat sink applications[J].Materials Science & Engineering, A. Structural Materials: Properties, Misrostructure and Processing,20081/2(1/2):39-44. |
| [6] | 章林;曲选辉;何新波;段柏华.高体积分数SiC/Cu复合材料的研究进展[J].粉末冶金技术,2008(3):224-229. |
| [7] | Martinez V.;Ordonez S.;Castro F.;Olivares L.;Marin J..Wetting of silicon carbide by copper alloys[J].Journal of Materials Science,200319(19):4047-4054. |
| [8] | 禹胜林;薛松柏;尹邦跃;黄薇.Al-Si电子封装材料粉末冶金法致密性研究[J].材料工程,2014(2):45-50. |
| [9] | Sundberg G;Paul P;Sung CM;Vasilos T.Identification and characterization of diffusion barriers for Cu/SiC systems[J].Journal of Materials Science,200513(13):3383-3393. |
| [10] | Yongzhong Zhan;Guoding Zhang.The effect of interfacial modifying on the mechanical and wear properties of SiC_p/Cu composites[J].Materials Letters,200329(29):4583-4591. |
| [11] | 王大伟;王美丽;李中翔;赵全亮;崔岩.溶胶-凝胶法制备BiFeO3粉体及其表征[J].材料工程,2014(12):50-54. |
| [12] | 刘猛;白书欣;李顺;赵恂;熊德赣.界面设计对Sip/Al复合材料组织和性能的影响[J].材料工程,2014(8):61-66. |
| [13] | 禇克 .高导热复合材料导热性能的研究[D].北京科技大学,2009. |
- 下载量()
- 访问量()
- 您的评分：
-
10%
-
20%
-
30%
-
40%
-
50%