为优化铝合金均匀化退火后的冷却工艺参数，采用动态电阻法、扫描电镜、透射电镜观察、能谱分析和硬度测试等方法，研究了均匀化处理后的冷却条件对Al－4％Cu合金组织性能的影响．获得的电阻率－温度曲线与材料的脱溶行为有良好的相关性．随着均匀化处理后冷却速率的降低，实验合金在冷却过程中会依次析出平衡相θ、亚稳相θ′和θ″．绘制了实验合金的CCT图，确定的脱溶敏感温度区间为500～300℃．选用合适的冷却工艺可以改善合金的组织性能，冷却时间超过1000 min，合金有较低的硬度和电阻率．当实验合金均匀化后冷却至室温的时间处于19．4～184．1 min时会析出θ″相，导致硬度和电阻率上升，不利于后续的塑性加工，应该尽量避免．
In order to optimize the cooling parameters after homogenization, the microstructure and properties evolutions during the cooling processes have been investigated by in?situ electrical resistivity measurements, scanning electron microscopy ( SEM) , transmission electron microscopy ( TEM) , energy dispersive spectrometer ( EDS) and hardness test. The result has shown that the electrical resistivity curves have a good agreement with the precipitation behaviors. There were three types of precipitates in the studied alloy under different cooling conditions. And the precipitation sequence was equilibrium θ phase, metastable θ′ phase and θ″ phase. The hardness?time and resistivity?time curves revealed that choosing a suitable cooling condition could improve the microstructures and performance of the alloy. The optimal cooling time was exceeding 1 000 min, so that the hardness and resistivity of the alloy was located in a low level. However, the cooling should avoid being finished in the 19.4~184.1 min. The precipitation of θ″phase in this range would lead to the increasing of hardness and resistivity, which was harmful to the subsequent plastic working.
参考文献
| [1] | 刘晓艳;潘清林;陆智伦;刘畅;何运斌;李文斌.Al-Cu-Mg-Ag耐热铝合金均匀化处理[J].材料科学与工艺,2011(04):28-32. |
| [2] | 李雪峰;张辉;蒋福林.新型Al-Mn合金均匀化处理过程中组织和性能演变[J].中国有色金属学报,2014(2):380-386. |
| [3] | 李红英;苏雄杰;尹浩;黄德胜.Al-Cu-Li-Mn-Zr-Ti合金在均匀化过程中的组织演变[J].中国有色金属学报（英文版）,2013(9):2543-2550. |
| [4] | Yan Liu;Darning Jiang;Wenlong Xie.Solidification phases and their evolution during homogenization of a DC cast Al-8.35Zn-2.5Mg-2.25Cu alloy[J].Materials Characterization,2014:173-183. |
| [5] | Haijun Wang;Ju Xu;Yonglin Kang.Study on inhomogeneous characteristics and optimize homogenization treatment parameter for large size DC ingots of Al-Zn-Mg-Cu alloys[J].Journal of Alloys and Compounds: An Interdisciplinary Journal of Materials Science and Solid-state Chemistry and Physics,2014:19-24. |
| [6] | 白素春;陈艳丽;胡云龙.大型铝合金简体铸件的质量控制[J].特种铸造及有色合金,2014(6):653-655. |
| [7] | 宋力强;刘浩;杜会军;高鹏.热压成形在车身上的典型应用与研究[J].材料科学与工艺,2014(2):49-54. |
| [8] | 李红英;宾杰;赵延阔;王晓峰.用原位电压法测定铝合金的CCT图[J].中国有色金属学报（英文版）,2011(9):1944-1949. |
| [9] | Li, H. Y.;Liu, J. J.;Yu, W. C.;Li, D. W..Development of non-linear continuous cooling precipitation diagram for Al-Zn-Mg-Cu alloy[J].Materials Science and Technology: MST: A publication of the Institute of Metals,201512(12):1443-1451. |
| [10] | 刘志华;刘瑞金.牛顿冷却定律的冷却规律研究[J].山东理工大学学报（自然科学版）,2005(6):23-27. |
| [11] | Milkereit, B.;Beck, M.;Reich, M.;Kessler, O.;Schick, C..Precipitation kinetics of an aluminium alloy during Newtonian cooling simulated in a differential scanning calorimeter[J].Thermochimica Acta: An International Journal Concerned with the Broader Aspects of Thermochemistry and Its Applications to Chemical Problems,20111/2(1/2):86-95. |
| [12] | Y. Zhang;B. Milkereit;O. Kessler.Development of continuous cooling precipitation diagrams for aluminium alloys AA7150 and AA7020[J].Journal of Alloys and Compounds: An Interdisciplinary Journal of Materials Science and Solid-state Chemistry and Physics,2014:581-589. |
| [13] | 王天资;巫瑞智;张景怀;刘滨.铝导电材料的研究进展[J].材料科学与工艺,2014(6):53-61. |
- 下载量()
- 访问量()
- 您的评分：
-
10%
-
20%
-
30%
-
40%
-
50%