基于三维有限元建立了六辊CVC辊系模型，该模型耦合了CVC辊形曲线、辊间轧制力分布以及带钢的弹塑性变形和辊系弹性变形，通过迭代计算辊间轧制力及轧辊与轧件的弹塑性变形。通过实际轧制规程数据对比验证了模型的有效性，其模拟计算结果与实际数据的绝对误差在10μm内，相对误差小于1%。采用该模型研究了板形控制机构如中间辊弯辊、中间辊窜辊和工作辊弯辊对带钢2次凸度和4次凸度的控制规律，并成功消除了生产现场宽薄带钢的边中复合浪缺陷。
By means of 3D Finite Element Method (FEM), a new 6-high CVC cold rolling mill model, which couples CVC profile, rolling force distribution between rolls, elastic deformation of rollers, and elastic-plastic deformation of strip, was built. The rolling force distribution between rolls and elastic-plastic deformation of roll and workpiece were obtained by the iteration calculation method. The model was verified in comparison with the actual rolling schedule data. The abso-lute error between the simulated results and the actual values is obtained to be less than 10μm, and relative error is less than 1%. Thus, the simulated results are in good agreement with the measured data. Consequently, the effect of flatness ac-tuators such as intermediate roll bending, intermediate roll shifting and work roll bending on secondary crown and quartic crown was studied and actual center-edge buckles of the industrial products of wide and thin strips in the cold rolling pro-cess were successfully eliminated according to the research results.
参考文献
| [1] | CHEN Xian-lin .Flatness Control in New Generation High-Tech Mill for Wide Strip Rolling[J].Journal of University of Science and Technology Beijing,1997,19(02):1. |
| [2] | Ginzburg V B.High-Quality Steel Rolling Theory and Practice[M].New York:MarcellDekker Inc,1993 |
| [3] | 连家创;戚向东.板带轧制理论与板形控制理论[M].北京:机械工业出版社,2013 |
| [4] | A.Seilinger,A.Mayrhofer,A.Kainz.SmartCroWn-改善轧机凸度和平直度控制的新系统[J].中国冶金,2003(01):42-44,38. |
| [5] | Guang Xu,Xianjun Liu,Jiarong Zhao,Junwei Xiong.Analysis of CVC roll contour and determination of roll crown[J].北京科技大学学报（英文版）,2007(04):378-380. |
| [6] | 孙静娜,薛涛,杜凤山.六辊CVC轧机接触应力与凸度控制的有限元分析[J].钢铁,2012(02):49-52. |
| [7] | 张云鹏;吴庆海;王长松.六辊CVC冷轧机板形控制性能研究[J].冶金设备,1998(06):8. |
| [8] | 刘宏民,郑振忠,彭艳.六辊CVC宽带轧机板形控制特性的计算机模拟[J].钢铁研究学报,2001(01):14-18. |
| [9] | SUN Jing-na;DU Feng-shan;LI Xue-tong.FEM Simulation of the Roll Deformation of Six-high CVC Mill in Cold Strip Roll-ing[A].US：Computer So-ciety Press,2008:412. |
| [10] | 王康健,白振华,刘卫.宝钢冷连轧机组末机架辊型改造策略的探讨[J].中国冶金,2012(06):22-25. |
| [11] | Furumoto H;Yamada K;Yanagimoto J .Effect of the Number of Work-Roll Surface Division on Prediction of Contact Length in Coupled Analysis of Roll and Deformation During Sheet Rolling[J].ISIJ International,2002,42(07):736. |
| [12] | 令狐克志,杨荃,何安瑞,赵林,郭晓波.宽带钢轧机辊间压力分布和轧制压力耦合求解[J].钢铁研究学报,2008(05):23-26. |
| [13] | 骆拓,邓华,赵世庆,李涵雄.基于影响函数法的轧制压力横向分布规律分析[J].机械强度,2010(01):165-170. |
- 下载量()
- 访问量()
- 您的评分：
-
10%
-
20%
-
30%
-
40%
-
50%