利用二维平面应变模型对Z-pin增强T型接头试样进行失效分析,采用内聚力模型模拟界面的破坏情况,通过在分层的上下界面加入非线性弹簧元模拟Z-pin的增强作用,非线性弹簧元的力学性能(桥联律)由细观力学方法获得,数值结果与试验值吻合较好.在已验证有限元方法的基础上,研究了Z-pin直径、密度及植入角度等对T型接头拉脱承载能力的影响.结果表明:Z-pin增强可显著提高T型接头的拉脱承载能力,与未Z-pin增强的T型接头相比,Z-pin增强明显延缓了掉载;T型接头的拉脱承载能力随Z-pin直径和密度的增加而增大,随植入角度的增大而减小;在所研究的角度范围内,当植入角度为60°时,T型接头的拉脱承载能力最好;Z-pin直径和密度对拉脱承载能力的影响远比植入角度的影响显著.
参考文献
| [1] | Venkata Dantuluri;Spandan Maiti;Philippe H. Geubelle;Rakesh Patel;Hakan Kilic.Cohesive modeling of delamination in Z-pin reinforced composite laminates[J].Composites science and technology,20073/4(3/4):616-631. |
| [2] | Marcello Grassi;Xiang Zhang.Finite element analyses of mode I interlaminar delamination in z-fibre reinforced composite laminates[J].Composites science and technology,200312(12):1815-1832. |
| [3] | Denis D.R. Cartie;Manos Troulis;Ivana K. Partridge.Delamination of Z-pinned carbon fibre reinforced laminates[J].Composites science and technology,20066(6):855-861. |
| [4] | G. Allegri;X. Zhang.On the delamination and debond suppression in structural joints by Z-fibre pinning[J].Composites, Part A. Applied science and manufacturing,20074(4):1107-1115. |
| [5] | D. D. R. Cartie;G. Dell'Anno;E. Poulin.3D reinforcement of stiffener-to-skin T-joints by Z-pinning and tufting[J].Engineering Fracture Mechanics,200616(16):2532-2540. |
| [6] | 郝继军;张佐光;张蕾;李敏;孙志杰.Z-pin植入参数对X-Cor夹层复合材料力学性能的影响[J].航空学报,2008(3):763-768. |
| [7] | 张向阳;李勇;褚奇奕;肖军;董晓阳.Z-pin点阵分布对层合板面内压缩性能的影响[J].航空学报,2014(1):195-202. |
| [8] | 张涛涛;周洪;史文华;燕瑛.Z-pin植入对二维机织复合材料层合板力学性能影响的数值模拟[J].复合材料学报,2014(2):295-303. |
| [9] | 单杭英;肖军;李宁;尚伟;张向阳.X-cor夹层结构的剪切模量实验与分析[J].材料工程,2014(5):59-65. |
| [10] | 段友社;郭书良;吴刚;侯军生.Z向增强泡沫夹芯复合材料冲击损伤及冲击后压缩性能[J].复合材料学报,2012(2):180-185. |
| [11] | 段沐枫;李宁;郑莹莹;肖军;李勇.K-cor夹层结构制备工艺[J].宇航材料工艺,2012(5):21-25. |
| [12] | D. D. R. CARTIE;B. N. COX;N. A. FLECK.Mechanisms of crack bridging by composite and metallic rods[J].Composites, Part A. Applied science and manufacturing,200411(11):1325-1336. |
上一张
下一张
上一张
下一张
计量
- 下载量()
- 访问量()
文章评分
- 您的评分：
-
10%
-
20%
-
30%
-
40%
-
50%