以碳化硅(SiC)和氧化铝(Al2O3)为起始原料、石墨为造孔剂, 通过原位反应结合工艺制备SiC多孔陶瓷. XRD分析表明多孔陶瓷的主相是SiC, 结合相是莫来石与方石英; SEM观察到多孔陶瓷具有相互连通的开孔结构. 坯体在烧结前后具有很小的尺寸变化, 线收缩率约在±1.5%内. 多孔陶瓷的开口孔隙率随烧结温度和成型压力的增大而减小,
随石墨加入量的增加而增大; 而体密度具有相反的变化趋势. 随着石墨粒径的增大, 多孔陶瓷的孔径分布呈现双峰分布. 抗弯强度随烧结温度和成型压力的增大而增大, 随石墨加入量的增大而减小. 于1450℃保温4h烧成的样品在0～800℃的平均热膨胀系数为6.4×10-6/K. 多孔陶瓷还表现出良好的透气性、抗高温氧化和耐酸腐蚀性, 但耐碱腐蚀性相对较差.
An in situ reaction-bonding technique was developed to fabricate porous silicon carbide (SiC) ceramics in air from SiC and Al2O3, using graphite as the pore former. The main phase is SiC and the bonded phases are mullite and cristobalite in porous SiC ceramics. The reaction-bonded SiC ceramics possess connected open pores. The linear shrinkage of the specimens before and after sintering is between --1.5% and +1.5%. Open porosity decreases with the sintering temperature and forming pressure, but increases with the graphite content. Bulk density and mechanical
strength increase with sintering temperature and forming pressure, but decrease with the graphite content. The pore size distribution takes on a bimodal distribution when the graphite particle size is 20.0μm. In addition, as-fabricated porous SiC ceramics exhibit low coefficient of thermal expansion, high N2 permeability, excellent high temperature-oxidation
resistance, good acid endurance and relatively bad alkaline endurance.
参考文献
| [1] | Green D J, Colombo P. MRS Bull., 2003, 28 (4): 296--300. [2] Greil P. Adv. Mater., 2002, 14 (10): 709--716. [3] She J H, Deng Z Y. J. Mater. Sci., 2002, 37 (17): 3615--3622. [4] Miwa S, Abe F, Hamanaka T, et al. SAE Paper, No. 2001-01-0192. [5] Montanaro L, Jorand Y, Fantozzi G, et al. J. Eur. Ceram. Soc., 1998, 18: 1339--1350. [6] Ding S, Zhu S, Zeng Y, et al. Ceram. 2006, 32 (4): 461--466. [7] 朱新文, 江东亮, 谭寿洪, 等(ZHU Xin-Wen, et al). 无机材料学报(Journal of Inorganic Materials), 2002, 17 (1): 79--85. [8] 刘岩, 黄政仁, 董绍明, 等(LIU Yan, et al). 无机材料学报(Journal of Inorganic Materials), 2005, 20 (2): 305--309. [9] Sepulveda P, Binner J G P. J. Eur. Ceram. Soc., 1999, 19: 2059--2066. [10] Meng G Y, Wang H T, Zheng W J. Mater. Lett., 2000, 45 (9): 224--227. [11] 佘继红, 林庆玲, 江东亮. 稀有金属材料与工程(Rare Metal Materials and Engineering), 2003, 32: 95--98. [12] Rice R W. J. Am. Ceram. Soc., 1981, 64 (6): 345--350. [13] Sweeney W T. J. Amer. Dental Assoc., 1933, 20: 108--119. |
- 下载量()
- 访问量()
- 您的评分：
-
10%
-
20%
-
30%
-
40%
-
50%