利用激光熔覆技术在钛表面预置硅粉原位制备了Ti5Si3涂层. 用XRD、SEM和TEM分析了涂层的组成和组织结构. 在UMT摩擦磨损试验机上对Ti5Si3涂层在不同载荷和不同滑动速度下的摩擦磨损性能进行了测试. 实验结果表明: 涂层的物相主要是Ti5Si3相和基材Ti相, 涂层的显微结构为球状和块状晶, Ti5Si3涂层具有较高的显微硬度, 涂层截面的平均显微硬度约为840 HV0.2, 是钛基材的4.4倍; Ti5Si3涂层可显著提高钛基材的耐磨性能; Ti5Si3涂层的磨损机理为磨粒磨损和粘着磨损.
Using silicon powder as the precursor to improve the wear resistance of Ti5Si3 coating was in situ successfully synthesized on Ti substrate by laser cladding. Friction and wear behavior of Ti5Si3 coatings under different normal loads and sliding speeds wear test conditions were evaluated using a UMT-2MT friction and wear tester. It is found that the prepared coating is mainly composed of Ti5Si3 and Ti phases. The high resolution transmission electron microscopy results confirm further the existence of Ti5Si3 compound in the prepared coating. Ti5Si3 coating has spherical and block-like microstructure. The Ti5Si3 coating shows a high average hardness of approximately 840 HV0.2, which is about 4.4 times as that of Ti substrate. Tribological properties of the prepared Ti5Si3 coating were systematically evaluated. It is found that the Ti5Si3 coating can improve the wear resistance of Ti. The wear mechanism of Ti5Si3 coating is abrasive and adhesive wear when sliding against GCr15 steel ball under all wear conditions.
参考文献
| [1] | |
| [2] | |
| [3] | |
| [4] | |
| [5] | |
| [6] | Bruni S, Martinesi M, Stio M, et al. Effects of surface treatment of Ti-6Al-4V titanium alloy on biocompatibility in cultured human umbilical vein endothelial cells. Acta Biomater., 2005, 1(2): 223-234.[2] DAS M, BALLA V K, BASU D, et al. Laser processing of SiC-particle-reinforced coating on titanium. Scr. Mater., 2010, 63(4): 438-441.[3] LI X M, LI Y S, HAN Y. Preparation of alumina coatings on titanium by cathodic micro-arc electrodeposition. Journal of Inorganic Materials, 2005, 20(6): 1493-1499.[4] GUO L T, LIU X C, GAO J Q, et al. Effect of titaniumsurface oxidation on the bonding strength of Ti-porcelain. Journal of Inorganic Materials, 2009, 24(5): 915-918.[5] GUO C, ZHOU J, ZHAO J, et al. Effect of ZrB2 on the microstructure and wear resistance of Ni-based composite coating produced on pure Ti by laser cladding. Tribol. Trans., 2011, 54(1): 80-86.[6] BAKER T N, SELAMAT M S. Surface engineering of Ti-6Al-4V by nitridingand powder alloying using CW CO2 laser. Mater. Sci. Technol., 2008, 24(4): 189-200.[7] YILDIZ F, YETIM A, ALSARAN A, et al. Plasma nitriding behavior of Ti6Al4V orthopedic alloy. Surf. Coat. Technol., 2008, 202(11): 2471-2476.[8] JIANG P, HE X L, LI X X, et al. Wear resistance of a laser surface alloyed Ti-6Al-4V alloy. Surf. Coat. Technol., 2000, 130: 24-28.[9] NOLAN D, HUANG S, LESKOVSEK V, et al. Sliding wear of titanium nitride thin films deposited on Ti-6Al-4V alloy by PVD and plasma nitriding processes. Surf. Coat. Technol., 2006, 200(20/21): 5698-5705.[10] LI Q J, WU H H, WANG J B, et al. Effects of pulse frequencies on properties of MAO coatings on pure titanium. Journal of Inorganic Materials, 2006, 21(2): 488-492.[11] GONG Y S, TU R, GOTO T. High-speed deposition of oriented TiNx films by laser metal-organic chemical vapor deposition. Journal of Inorganic Materials, 2010, 25(4): 391-395.[12] ZHANG S, ZHANG C H, WU W T, et al. An in situ formed TiC particle reinforcement composite coating induced by laser melting on surface of alloy Ti6Al4V and its wearing performance. Acta Metall. Sinica, 2001, 37(3): 315-320.[13] GUO C, ZHOU J, ZHAO J, et al. Microstructure and friction and wear behavior of laser boronizing composite coatings on titanium substrate. Appl. Surf. Sci., 2011, 257(9): 4398-4405.[14] GUO B, ZHOU J, ZHANG S, et al. Phase composition and tribological properties of Ti&ndash |
- 下载量()
- 访问量()
- 您的评分：
-
10%
-
20%
-
30%
-
40%
-
50%