研究了V-5Cr-5Ti合金在900~1100 ℃之间的再结晶规律, 概括了V-5Cr-5Ti合金的再结晶动力学机制. 结果表明, 合金冷变形板材在950~1050 ℃下退火处理, 可获得细小、均匀的等轴晶; 初步推导了V-5Cr-5Ti合金再结晶动力学机制, 符合Avrami-Erofeev形核长大机制; 并计算了V-5Cr-5Ti合金再结晶激活能Q_r, 其值为261.91~289.67 kJ· mol~(-1).
The recrystallization of V-5Cr-5Ti alloy annealed at 900~1100 ℃ was investigated. The recrystallization kinetics of the alloy was summarized. The results showed that the fine and uniform equiaxed grains were obtained when the cold working alloy annealed at 950~1050 ℃. Recrystallization dynamic mechanism of cold-working V-5Cr-5Ti alloy was established preliminarily, which accorded with Avrami-Erofeev mechanism of nucleation and growth. Recrystallization activation energy Q_r of V-5Cr-5Ti alloy was obtained, Q_r=261.91~289.67 kJ·mol~(-1).
参考文献
[1] | Satou M;Abe K;Kayana H.High-temperature deformation of modified V-Ti-Cr-Si type alloys[J].Journal of Nuclear Materials,1991(179-181):757. |
[2] | Dediurin A I;Platov Yu M;Zsakharova M I;Borovitskaja I V Artemov N A.Effect of neutron irradiation on swelling,elastic modulus and thermal conductivity of V-Ga alloys[J].Journal of Nuclear Materials,1998(258-263):1409. |
[3] | Evtikin V A;Lyublinski I E;Vertkov A V;Korjavin V M.Lithium-vanadium experimental facility for blanket problems investigation[J].Fusion Engineering and Design,1995(27):731. |
[4] | Kurtz R J;Hamilton M L;Li H.Grain boundary chemistry and heat treatment effects on the ductile-to-brittle transition behavior of vanadium alloys[J].Journal of Nuclear Materials,1998(258-263):1375. |
[5] | Li Huaxin;Hamilton M L;Jones R H .Effect of heat treatment on grain boundary chemistry and fracture properties of a V-5Cr-5Ti alloy[J].Scripta Metallurgia et Materials,1995,33(07):1063. |
[6] | 宋维锡.金属学[M].北京:冶金工业出版社,1989 |
[7] | 李兴无,路民旭,沙爱学,张雷.退火温度对Ti-3Al-4.5V-5Mo钛合金显微组织和织构的影响[J].稀有金属,2008(02):144-150. |
[8] | 付艳艳,宋月清,惠松骁,米绪军,叶文君.热处理对VST55531钛合金的组织和拉伸性能的影响[J].稀有金属,2008(04):399-403. |
[9] | 潘金生;仝健民;田民波.材料科学基础[M].北京:清华大学出版社,1998 |
[10] | 葛庆仁.气固反应动力学[M].北京:原子能出版社,1991 |
[11] | 于振涛,周廉,邓炬,顾海澄.Ti-2Al-2.5Zr合金再结晶特性及动力学机制[J].稀有金属材料与工程,1999(06):340-344. |
- 下载量()
- 访问量()
- 您的评分:
-
10%
-
20%
-
30%
-
40%
-
50%