分析了影响真空辅助成型技术(VARI)工艺成型复合材料的纤维体积分数和厚度均匀性的关键因素,即VARI成型工艺的树脂流动控制形式、纤维预制体状态、织物状态、树脂黏度,通过试验分析了各因素对VA-RI成型复合材料厚度和纤维体积分数的影响.试验结果表明,采用HFVI(high fiber-volume vacuum infusion)工艺、BA9914树脂及真空处理后的U3160单向机织物成型的纤维增强树脂复合材料层合板,其纤维体积分数和厚度均匀性能够接近预浸料/热压罐成型的复合材料制件的水平.
参考文献
| [1] | Niggemann C,Song Y S,Gillespie J W,et al.Experimental investigation of the controlled atmospheric pressure resin infusion (CAPRI) process[J].Journal of Composite Materials,2008,42(11):1049-1061. |
| [2] | Thomas K T.Interlayer toughening of composite materials[J].Polymer Composites,2009,30 (1):70-86. |
| [3] | 魏俊伟,张用兵,郭万涛.真空辅助成型(VARI)工艺研究进展[J].材料开发与应用,2010(3):99-104.Wei Junwei,Zhang Yongbing,Guo Wantao.Development of vacuum assisted resin lnfusion (VARI)[J].Development and Application of Materials,2010(3):99-104. |
| [4] | 胡晓睿.复合材料整体结构成形.降低飞行器制造成本[J].国防制造技术,2011(1):16-17.Hu Xiaorui.Overall structure composite material forming.Lower down the cost of aircraft manufacturing[J].Defense Manufacturing Technology,2011 (1):16-17. |
| [5] | Thomas L R,Miller A K,Chan A L.Fabrication of complex high-performance composite structures at low cost using VARTM[J].SAMPEProceedings,2002,47:1317-1329. |
| [6] | 赵渠森,赵攀峰.真空辅助成型技术(二)[J].高科技纤维与应用,2002,27(4):21-26,39.Zhao Qusen,Zhao Panfeng.VARI-vacuum assisted resin infusion (2)[J].Hi-tech Fiber & Application,2002,27(4):21-26,39. |
| [7] | 赵渠森,赵攀峰.真空辅助成型技术(三)[J].高科技纤维与应用,2002,27(5):25-27.Zhao Qusen,Zhao Panfeng.VARI-vacuum assisted resin infusion (3)[J].Hi techFiber & Application,2002,27(5):25-27. |
| [8] | 苏峰,于洋,于柏峰.真空辅助树脂灌注工艺的创新性改进[J].纤维复合材料,2010(1):18-20.Su Feng,Yu Yang,Yu Bofeng.Innovative improvement of vacuum assisted resin infusion (VARI) process[J].Fiber Composites,2010(1):18-20. |
| [9] | 祝颖丹,李新华,王继辉,等.高渗透介质型真空注射成型工艺的研究[J].复合材料学报,2003,20(4):136-140.Zhu Yingdan,Li Xinhua,Wang Jihui,et al.Study on molding process based on a high-permeable medium[J].Acta Materiae Compositae Sinica,2003,20(4):136-140. |
| [10] | Heider D,Chandrabalan S,Eksik O,et al.Pressure behavior during vacuum assisted processing[J].SAMPE Proceedings,2009,54:1376-1383. |
| [11] | Thomas K T,Milham C,Howe C,et al.New out-ofautoclave materials and processes for aerospace applications[J].SAMPE Proceedings,2009,54:388-401. |
| [12] | 陶积柏,王绍凯,李敏,等.三维夹芯层连织物复合材料真空辅助成型工艺影响因素[J].复合材料学报,2010,27(4):81-86.Tao Jibai,Wang Shaokai,Li Min,et al.Influence factors of vacuum assisted resin transfer molding proeess for 3D spacer fabric composites[J].Acta Materiae Compositae Sinica,2010,27(4):81-86. |
| [13] | 潘利剑,刘卫平,陈萍,等.真空辅助成型工艺中预成型体的厚度变化与过流控制[J].复合材料学报,2012(5):244-248.Pan Lijian,Liu Weiping,Chen Ping,et al.Change in preform thickness throughout the vacuum assisted resin infusion process and the post-filling control[J].Acta Materiae Compositae Sinica,2012(5):244-248. |
| [14] | 孙占红,李小兵,郑洪亮.Q/ZHFC1101.1-2013BA9912环氧树脂[S].北京:中航复合材料有限责任公司,201 3.Sun Zhanhong,Li Xiaobing,Zheng Hongliang.Q/ZHFC 1101.1-2013 BA9912 epoxy resin[S].Beijing:AVIC Composite Corporation Ltd,2013. |
| [15] | 刘 强,赵 龙,黄 峰.Q/ZHFC 1101.3 2013 G0827/BA9912复合材料真空辅助树脂渗透工艺[S].北京:中航复合材料有限责任公司,2013.Liu Qiang,Zhao Long,Huang Feng.Q/ZHFC 1101.3-2013 G0827/BA9912 Vacuum assisted resin infusion process of composite[S].Beijing:AVIC Composite Corporation Ltd,2013. |
| [16] | 孙占红,王新庆,潘翠红,等.Q/9S 125.6-2010 U3160/BA9914树脂传递模塑成型复合材料体系[S].北京:北京航空制造工程研究所,2010.Sun Zhanhong,Wang Xinqing,Pan Cuihong,et al.Q/9S 125.6-2010 U3160/BA9914 resin transfer molding composite material system[S].Beijing:Beijing Aviation Manufacturing Technology Research Institute,2010. |
| [17] | 李小兵,孙占红,曹正华.真空辅助成型技术及其配套基体树脂研究进展[J].热固性树脂,2006,21(5):39-43,53.Li Xiaobing,Sun Zhanhong,Cao Zhenghua.Research development of VARI molding technology and its matrix resin[J].Thermosetting Resin,2006,21(5):39-43,53. |
上一张
下一张
上一张
下一张
计量
- 下载量()
- 访问量()
文章评分
- 您的评分：
-
10%
-
20%
-
30%
-
40%
-
50%