欢迎登录材料期刊网

材料期刊网

高级检索

利用Baker模型和弹塑性有限元方法研究了胶接接头搭接区残余应力的分布.结果表明,因胶粘荆的线膨胀系数比被粘物高得多,胶层固化时被粘物阻碍了胶层的收缩,故胶层中为残余拉伸应力,被粘物中为残余压缩应力,胶层中的残余应力远大于被粘物中的残余应力.利用Baker模型和有限元计算远离自由端的胶层中的残余应力,两者吻合.被粘物中的残余应力呈中心对称,等效应力经多项式拟合后呈抛物线分布.

The Baker model and elasto-plastic finite element method(FEM) are applied to investigate the thermal stress distribution in over lap zone of the single lap joint. The results obtained show that tensile stress in the adhesive and residual compressive stress in the adherend as big difference of thermal coefficient of expansion between the two materials. The results of theoretical calculation and numerical investigation on the thermal stress distribution in the adhesive away from the end are anastomotic. The residual stress in the adherend is center symmetric, and the polynomial fitting of the S_(eqv) is obtained as parabola distribution.

参考文献

[1] 游敏;郑小玲.胶接强度分析及应用[M].武汉:华中科技大学出版社,2009
[2] 李智,游敏,丰平.胶接接头界面理论及其表面处理技术研究进展[J].材料导报,2006(10):48-51.
[3] Karthik R;Zhao W .Evolution residual stresses in thermoplastic bonding to metals[J].International Journal of Adhesion and Adhesives,1997,17(04):353.
[4] Anifantis N K;Kakavas P A;Papanicolaou G C .Thermal stress concentration due to imperfect adhesion in fiber reinforced composites[J].Composites Science and Technology,1997,57(06):687.
[5] 翁熙祥.粘接理论研究的一些新进展[J].中国胶粘剂,1999(05):38-39.
[6] Lee S J;Lee D G .Optimal-design of the adhesively bonded tubular single lap joint[J].Journal of Adhesion,1995,50(2-3):165.
[7] Kim Y G;Lee S J;Lee D G et al.Strength analysis of adhesively bonded tubular single lap steel-steel joints under axial loads considering residual thermal stresses[J].Journal of Adhesion,1997,60(1-4):125.
[8] Cho J H;Kong D I;Park C E et al.Effect of curing temperature on the adhesion strength of polyamideimide/ copper joints[J].Journal of Adhesion Science and Technology,1998,12(05):507.
[9] Humfeld G R;Dillard D A .Residual stress development in adhesive joints subjected to thermal cycling[J].Journal of Adhesion,1998,65(1-4):277.
[10] A.Abedian;W.Szyszkowski .Effects of surface geometry of composites on thermal stress distribution: a numerical study[J].Composites science and technology,1999(1):41-54.
[11] Apalak M K;Gunes R .On non-linear thermal stresses in an adhesively bonded single lap joint[J].Computers & Structures,2002,80:85.
[12] 游敏,郑小玲,郑勇.金属胶接接头的内应力及其消除[J].中国胶粘剂,1996(03):26-28,42.
[13] 王遵,肖加余,曾竟成,杨孚标.复合材料胶接修复金属构件残余热应力研究进展[J].机械工程材料,2007(04):5-8.
[14] Baker A A;Jones R.Bonded repair of aircraft structures[M].Dordrecht:Martinus Nijhoff,1988:122.
[15] 杜建军,姚英学.金属胶接接头内应力研究新进展[J].宇航材料工艺,2001(05):1-5.
上一张 下一张
上一张 下一张
计量
  • 下载量()
  • 访问量()
文章评分
  • 您的评分:
  • 1
    0%
  • 2
    0%
  • 3
    0%
  • 4
    0%
  • 5
    0%