建立了桥联纤维细观力学模型,研究了界面对纤维增强陶瓷基复合材料拉伸模量及强度的影响.分别引入纤维应力均匀系数和界面脱粘率作为界面完伞脱粘和局部脱粘条件下界面性能的表征参数.研究表明,应力均匀系数及界面脱粘率越大,材料模量越低,而断裂时纤维所承担的应力越高.基于混合率给出了拉伸强度表达式,同时也分析了基体裂纹分布、界面脱粘和纤维拔出对强度的影响.计算结果表明,本文强度模型给出的预测值与试验值吻合较好.
参考文献
[1] | 隋万美.陶瓷基复相材料的非相变增韧机制[J].中国陶瓷,2000,36(1):4-8.Sui Wanmei.Toughing mechanism of non-phase transformation in multiphase ceramics[J].China Ceramics,2000,36(1):4-8. |
[2] | 梅辉.2D C/SiC在复杂耦合环境中的损伤演变和失效机制[D].西安:西北工业大学,2007. |
[3] | 管国阳,矫桂琼,张增光.2D-C/SiC复合材料的宏观拉压特性和失效模式[J].复合材料学报,2005,22(4):81-85.Guan Guoyang,Jiao Guiqiong,Zhang Zengguang.Uniaxial macro-mechanical property and failure mode of a 2D-woven C/SiC composite[J].Acta Materiae Compositae Sinica,2005,22(4):81-85. |
[4] | Zeng Q D,Wang Z L,Ling L.A study of the influence of interfacial damage on stress concentrations in unidirectional composites[J].Composites Science and Technology,1997,57.129-135. |
[5] | Curtin W A,Ahn B K,Takeda N.Modeling brittle and tough stress strain behavior in unidirectional ceramic matrix composites[J].Acta Mater,1998,46(10),3409-3420. |
[6] | Evans A G,Marshall D B.The mechanical behavior of ceramic matrix composites[J].Acta Metallurgica,1989,37(10):2567-2583. |
[7] | Cao H,Thouless M D.Tensile tests of ceramic matrix composites:Theory and experiment[J].J Am Ceram Soc,1990,73(7):2091-2094. |
[8] | Kagawa Y,Fujita T,Okura A.Temperature dependence of tensile mechanical properties in SiC fiber-reinforced Ti matrix composites[J].Acta Metall Mater,1994,42(9):3019-3026. |
[9] | Thomas H,Herwig P,Karl K.Coating of carbon fibers:The strength of the fibers[J].J Am Ceram Soc,1995,78(l):133-136. |
[10] | 张增光.2D C/SiC复合材料的弹性常数预测及失效模式研究[D].西安:西北工业大学,2005. |
[11] | Mei H,Cheng L F,Zhang L,et al.Modeling the effects of thermal and mechanical load cycling on a C/SiC composite in oxygen/argon mixtures[J].Carbon,2007,45:2195-2204. |
上一张
下一张
上一张
下一张
计量
- 下载量()
- 访问量()
文章评分
- 您的评分:
-
10%
-
20%
-
30%
-
40%
-
50%