对6016铝合金激光焊接接头的力学性能开展研究,分析焊后时效热处理对其力学性能的影响规律.结果表明:焊后时效处理可以提高焊接接头的力学性能,采用(180℃+10h)时效处理工艺可将焊缝中心的硬度从58HV提高到82 HV,可将焊接接头的拉伸强度从180MPa提高到274MPa,时效强化效果明显.动力学分析表明,6016铝合金焊接接头时效强化过程符合Johnson-Mehl-Avrami (JMA)方程.当时效温度升高,接头中强化相体积分数的变化率也随之增大,合金硬度上升速率增加,达到峰值硬度所需时间变短.
参考文献
[1] | J.M. Sanchez-Amaya;Z. Boukha;M.R. Amaya-Vazquez.Analysis of the Laser Weldability under Conduction Regime of 2024, 5083, 6082 and 7075 Aluminium Alloys[J].Materials Science Forum,2012:7-12. |
[2] | Ascari, A.;Fortunato, A.;Orazi, L.;Campana, G..The influence of process parameters on porosity formation in hybrid LASER-GMA welding of AA6082 aluminum alloy[J].Optics & Laser Technology,20125(5):1485-1490. |
[3] | Bergmann, Jean Pierre;Bielenin, Martin;Feustel, Thomas.Aluminum welding by combining a diode laser with a pulsed Nd:YAG laser[J].Welding in the World: Journal of the International Institute of Welding: Journal of the International Institute of Welding,20152(2):307-315. |
[4] | Engler, Olaf;Schaefer, Carmen;Myhr, Ole Runar.Effect of natural ageing and pre-straining on strength and anisotropy in aluminium alloy AA 6016[J].Materials Science & Engineering, A. Structural Materials: Properties, Misrostructure and Processing,2015:65-74. |
[5] | Tricia A. Bennett;Jurij Sidor;Roumen H. Petrov;Leo A. I. Kestens.The Effect of Intermediate Annealing on Texture Banding in Aluminum Alloy 6016[J].Advanced Engineering Materials,201010(10):1018-1023. |
[6] | A .Perovic;D. D. Perovic;G.C. Weatherly;D. J. Lloyd.Precipitation in Aluminum Alloys AA6111 and AA6016[J].Scripta materialia,19997(7):.703—708-0. |
[7] | 张巧霞;郭明星;胡晓倩;曹零勇;庄林忠;张济山.汽车板用Al-0.6Mg-0.9Si-0.2Cu合金时效析出动力学研究[J].金属学报,2013(12):1604-1610. |
[8] | T. Moons;P. Ratchev;P. De Smet;B. Verlinden;P. Van Houtte.A comparative study of two Al-Mg-Si alloys for automotive applications[J].Scripta materialia,19968(8):939-945. |
[9] | 常丽艳;宋西平;李宏良;吴圣川.7075铝合金激光-MIG复合焊接接头组织及性能的分析[J].热加工工艺,2014(9):25-28. |
[10] | P.W.J. Mckenzie;R. Lapovok.ECAP with back pressure for optimum strength and ductility in aluminium alloy 6016--Part 1: Microstructure[J].Acta materialia,20109(9):3198-3211. |
[11] | Kenji Matsuda;Daisuke Teguri;Yasuhiro Uetani;Tatsuo Sato;Susumu Ikeno.Cu-segregation at the Q'/α-Al interface in Al-Mg-Si-Cu alloy[J].Scripta materialia,200212(12):833-837. |
[12] | 易杰;蒋斌.6061铝合金时效工艺和动力学模型研究[J].轻合金加工技术,2014(7):30-36. |
[13] | A. Gaber;M.A. Gaffar;M.S. Mostafa.Precipitation kinetics of Al-1.12 Mg2Si-0.35 Si and Al-1.07 Mg_2Si-0.33 Cu alloys[J].Journal of Alloys and Compounds: An Interdisciplinary Journal of Materials Science and Solid-state Chemistry and Physics,20071/2(1/2):167-175. |
上一张
下一张
上一张
下一张
计量
- 下载量()
- 访问量()
文章评分
- 您的评分:
-
10%
-
20%
-
30%
-
40%
-
50%