The hot deformation behavior of a Ti-47Al-2Cr-2Nb-0.2W-0.15B (at.%) titanium aluminide alloy fabricated by pre-alloyed powder metallurgy has been investigated by using the hot compression tests in the temperature range from 950°C to 1300°C and at the strain rates between 10-3 s-1 and 10 s-1. The processing maps have been established to evaluate the optimum hot processing conditions and reveal the instability regions. It is found that the flow stress of the investigated alloy is a strong function of the temperature and the strain rate. The investigated alloy has the optimum hot-working condition at 950°C and 10-3 s-1, since the material undergoes dynamic recrystallization to produce a fine-grained microstructure. At 1250°C and 10-3 s-1, the alloy exhibits superplastic deformation. At 1300°C and 10-1 s-1, the cyclic dynamic recrystallization with high temperature grain coarsening takes place. The material undergoes flow instabilities at lower temperatures and higher strain rates, as predicted by the instability criterion. The processing maps demonstrate that the strain significantly affected the instability regions. The manifestations of the instabilities have been observed in the form of microvoids, wedge cracks, and surface fractures.
参考文献
| [1] | W. Sha and S. Malinov: Titanium Alloys: Modelling of Microstructure, Properties and Applications, Woodhead Publishing, Cambridge, 2009, 588.[2 ] D.M. Dimiduk: Mater. Sci. Eng. A, 1999, 263, 281.[3 ] M. Thomas, O. Berteaux, F. Popoff, M.P. Bacos, A. Morel, B. Passilly and V. Ji: Intermetallics, 2006, 14, 1143.[4 ] G. Das, H. Kestler, H. Clemens and P.A. Bartolotta: JOM, 2004, 56, 42.[5 ] C. Koeppe, A. Bartels, H. Clemens, P. Schretter and W. Glatz: Mater. Sci. Eng. A, 1995, 201, 182.[6 ] A. Lasalmonie: Intermetallics, 2006, 14, 1123.[7 ] R.M. Imayev, V.M. Imayev, M. Oehring and F. Appel: Intermetallics, 2007, 15, 451.[8 ] J.H. Moll and B.J. McTiernan: Metal Powder Report, 2000, 55, 18.[9 ] R. Gerling, H. Clemens and F.P. Schimansky: Adv. Eng. Mater., 2004, 6, 23.[10] Y.V.R.K. Prasad and S. Sasidhara: Hot Working Guide: A Compendium of Processing Maps, ASM International, Warrendale, 1997, 6.[11] Y.V.R.K. Prasad and T. Seshacharyulu: Int. Mater. Rev., 1998, 43, 243.[12] N. Srinivasa and Y.V.R.K. Prasad: J. Mater. Process. Technol., 1995, 51, 171.[13] F.A. Slooff, J.P. Boomsma, J. Zhou, J. Duszczyk and L. Katgerman: Data Correction for Constitutive Analysis of Wrought Magnesium Alloys Based on Compression Tests, in Magnesium, Wiley-VCH, Weinheim, 2007, 324.[14] Y.V.R.K. Prasad, D.H. Sastry and S.C. Deevi: Intermetallics, 2000, 8, 1067.[15] I. Weiss and S.L. Semiatin: Mater. Sci. Eng. A, 1999, 263, 243.[16] J. Sun, J.S. Wu and Y.H. He: Int. J. Mater. Res., 2000, 91, 472.[17] W.B. Lee, H.S. Yang, Y.W. Kim and A.K. Mukheriee: Scripta Mater., 1993, 29, 1403.[18] S.C. Cheng, J. Wolfenstine and O.D. Sherby: Metall. Mater. Trans. A, 1992, 23, 1509.[19] T. Takahashi, H. Nagai and H. Oikawa: Mater. Sci. Eng. A, 1990, 128, 195.[20] M.F. Ashby and R.A.Verrall: Acta Mater., 1973, 21, 149.[21] Y.V.R.K. Prasad and T. Seshacharyulu: Mater. Sci. Eng. A, 1998, 243, 82.[22] R. szkowski, J. Bystrzycki and T. Plocinski: Intermetallics, 2010, 18, 1344.[23] Y. Liu, R. Hu, J.S. Li, H.C. Kou, H.W. Li, H. Chang and H.Z. Fu: J. Mater. Process. Technol., 2009, 209, 4020.[24] T. Sakai and J.J. Jonas: Acta Mater., 1984, 32, 189.[25] S. Anbuselvan and S. Ramanathan: Mater. Design., 2010, 31, 2319.[26] D.Watkins, H.R. Piehler, V. Seetharaman, C.M. Lombard and S.L. Semiatin: Metall. Mater. Trans. A, 1992, 23, 2669.[27] S.L. Semiatin and V.A. Seetharaman: Scripta Mater., 1997, 36, 291.[28] Y.C. Lin, M.S. Chen and J. Zhong: Comput. Mater. Sci., 2008, 44, 316.[29] M. Kazeminezhad: Mater. Sci. Eng. A, 2008, 486, 202. |
- 下载量()
- 访问量()
- 您的评分：
-
10%
-
20%
-
30%
-
40%
-
50%