采用维氏硬度、拉伸力学性能测试、扫描电镜和透射电子显微镜分析手段,研究了断续时效对含Ag的Al-Cu-Mg基合金的组织和性能的影响。结果表明：185℃高温欠时效Al-Cu-Mg-Ag合金在低温进行二次时效时,会发生二次析出现象,合金塑性显著提高。随着185℃欠时效时间的延长,合金二次时效初始硬度升高,峰值时间缩短,峰值硬度增量降低。二次时效温度为65℃时,合金中主要强化相为G.P.区和少量的Ω相,其峰值强度硬度低于T6态,提高二次时效温度至150℃,合金主要强化相为Ω相和少量的G.P.区,其峰值强度硬度略高于T6态。
The effects of interrupted ageing on microstructure and mechanical properties of Al-Cu-Mg alloy with trace Ag were investigated by means of Vickers hardness test（HV）,tensile test,scanning electron microscopy（SEM） and transmission electron microscopy（TEM）.The results show that if Al-Cu-Mg-Ag alloy was underaged at 185℃,and then hold at a lower temperature,the alloy will undergo so-called ＇secondary precipitation＇.And the plasticity of the alloy will be improved.If the time of underageing at 185℃ is elongated,the initial hardness of secondary ageing increases,and both the time of peak hardness and the net hardness increment are reduced.When the secondary aging temperature is 65℃,the dominant hardening precipitates are G.P.zones.The mechanical properties,hardness and strength are lower than those of the peak-aged alloy of T6 temper.But if the secondary aging temperature is elevated to 150℃,the dominant hardening precipitates will be changed to Ω phases,and the mechanical properties of alloy will also be improved.
参考文献
| [1] | 刘志义,李云涛,刘延斌,夏卿坤.Al-Cu-Mg-Ag合金析出相的研究进展[J].中国有色金属学报,2007(12):1905-1915. |
| [2] | Xiao Daihong;Wang Jiannong;Chen Kanghua;Huang Baiyun .Superplastic deformation of a heat-resistant Al-Cu-Mg-Ag-Mn alloy[J].Journal of Materials Processing Technology,2009(7):3300-3305. |
| [3] | 宋旼,陈康华,黄兰萍.Al-Cu-Mg-（Ag）合金中时效析出相的析出及生长动力学[J].中国有色金属学报,2006(08):1313-1319. |
| [4] | Peel C J.Aluminum-Lithium Alloys VI[M].Oberursel:DGM Informationsgesellsehaft,1992:1259. |
| [5] | Itoh G;Kanno M;Hagiwara T et al.Embrittlemertt in an agehardened 2091 aluminum alloy by exposure at elevated temperatures below the aging temperature[J].Acta Materialia,1999,47:3799-3809. |
| [6] | Noble B;Harris S J;Dinsdale K .Reduction of Toughness in Aluminium-Lithium Alloys Caused by Long Term Exposure at Low Temperatures[J].Materials Science Forum,2000,331-337:1353. |
| [7] | LumleyRN;Morton A J;Pomear I J .Enhanced creep performance in an AI-Cu-Mg-Ag alloy through underageing[J].Acta Materialia,2002,50:3597-3608. |
| [8] | Lumley R N;Polmear I J;Morton A J .International Patent[P].Application PCT/AU00/01601,2002. |
| [9] | Lumley R N;Polrnear I J;Morton A J .International Patent[P].Application PCT/AU02/00234,2002. |
| [10] | Lumley R N;Buha J;Polmear I J et al.Secondary precipitation in aluminium alloys & its role in modern heat treatment[J].Materials Science Forum,2006,519:521:283-521:290. |
| [11] | J. Buha;R.N. Lumley;A.G. Crosky .Secondary precipitation in an Al-Mg-Si-Cu alloy[J].Acta materialia,2007(9):3015-3024. |
| [12] | Effort O;Solenthaler C;Speidel M O .[J].Materials Science and Engineering A,1995,191:113-120. |
| [13] | 朱宝宏,熊柏青,张永安,熊益民.热处理工艺对微量Mn、Zr作用下的高纯Al-Cu-Mg-Ag合金性能的影响[J].稀有金属材料与工程,2010(01):144-148. |
| [14] | 张坤,戴圣龙,黄敏,杨守杰,颜鸣皋.高纯Al-Cu-Mg-Ag合金的多级断续时效工艺研究[J].航空材料学报,2007(04):1-5. |
| [15] | Hutchinson C R;Fan X;Pennycook S J et al.On the origin of the high coarsening resistance of Ω plates in A1-Cu-Mg-Ag Alloys[J].Acta Materialia,2001,49:2827-2841. |
- 下载量()
- 访问量()
- 您的评分：
-
10%
-
20%
-
30%
-
40%
-
50%