Effects of Butt Design and Gap Width on the Microstructure and Mechanical Properties of Magnesium Alloy Welds

材料科学技术（英文）, 2012, 28(6): 537-542.

Effects of Butt Design and Gap Width on the Microstructure and Mechanical Properties of Magnesium Alloy Welds

^1, , ^2, , ^3,

1.School of Materials Science and Engineering, Dalian University of Technology, Dalian 116085, China State Key Laboratory of Advanced Welding and Joining, Harbin Institute of Technology, Harbin 150001, China

2.School of Materials Science and Engineering, Dalian University of Technology, Dalian 116085, China

3.School of Materials Science and Engineering, Dalian University of Technology, Dalian 116085, China

关键词：力学性能 , 对接设计 , 合金焊接 , 微观结构 , 间隙 , 扫描电子显微镜 , 显微硬度计 , 拉伸强度

Effects of Butt Design and Gap Width on the Microstructure and Mechanical Properties of Magnesium Alloy Welds

Honggang Dongi ^1, , Chuanqing Liao ^2, , Liqun Yang ^3,

2.School of Materials Science and Engineering, Dalian University of Technology, Dalian 116085, China

3.School of Materials Science and Engineering, Dalian University of Technology, Dalian 116085, China

Keywords： Magnesium , Gas tungsten arc welding , Butt design , Gap width , Pore , Mechanicalproperties ,

The effects of parallel and angular butt designs with different gap widths on the microstructure and mechanical properties of the resultant magnesium joints in gas tungsten arc welding were investigated. The experimental results displayed that the tensile strength of the joint made with angular butt joint and 0.3 ram-wide gap reached 266 MPa, the joint fractured through the heat-affected zone or base metal during tensile testing, and the microstructure examination showed that no macropore appeared in the fusion zone. However, macropores in diameter of larger than 200 micron occurred for other joint designs, the tensile strength of the resultant joints decreased, and the joints fractured through the fusion zone during tensile testing. The fracture surfaces were examined by scanning electron microscopy and the microhardness distribution in the joints was measured by using a Vickers microhardness tester.

参考文献

[1]	L. Commin;M. Dumont;J.-E. Masse .Friction stir welding of AZ31 magnesium alloy rolled sheets: Influence of processing parameters[J].Acta materialia,2009(2):326-334.
[2]	W. B. Lee;Y. M. Yeon;S. B. Jung .Joint properties of friction stir welded AZ31B -H24 magnesium alloy[J].Materials Science and Technology: MST: A publication of the Institute of Metals,2003(6):785-790.
[3]	G. Song;P. Wang .Pulsed MIG welding of AZ31B magnesium alloy[J].Materials Science and Technology: MST: A publication of the Institute of Metals,2011(2):518-524.
[4]	L.M. LIU;Z.D. ZHANG;G. SONG .Mechanism and Microstructure of Oxide Fluxes for Gas Tungsten Arc Welding of Magnesium Alloy[J].Metallurgical and Materials Transactions, A. Physical Metallurgy and Materials Science,2007(3):649-658.
[5]	X. Cao;M. Jahazi;J.P. Immarigeon .A review of laser welding techniques for magnesium alloys[J].Journal of Materials Processing Technology,2006(2):188-204.
[6]	M. FURUKAWA;Z. HORITA;M. NEMOTO .MICROHARDNESS MEASUREMENTS AND THE HALL-PETCH RELATIONSHIP IN AN Al-Mg ALLOY WITH SUBMICROMETER GRAIN SIZE[J].Acta materialia,1996(11):4619-4629.

上一张下一张

计量

下载量()
访问量()

作者相关

在本站搜索
在百度学术搜索
在万方数据库搜索
在CNKI搜索

文章评分

您的评分：
1

0%
2

0%
3

0%
4

0%
5

0%

材料期刊网

Effects of Butt Design and Gap Width on the Microstructure and Mechanical Properties of Magnesium Alloy Welds

Effects of Butt Design and Gap Width on the Microstructure and Mechanical Properties of Magnesium Alloy Welds

参考文献