Pure copper and its composites reinforced with Ni3Al particles were produced by powder metallurgy （PM）. Ni3Al powders were produced by mechanical ball milling from vacuum arc melted compounds. The Ni3Al powders were characterized by X-ray diffraction （XRD）. The microscopy examinations revealed that the Ni3Al particles were distributed uniformly in the matrix. The effects of the particle fraction on the density, electrical conductivity, strength and dry sliding wear resistance of composite were investigated. It was found that the density and electrical conductivity of the composites decrease while the compression yield strength and wear resistance of composites increase with an increase in the particle fraction. The dry sliding wear tests were performed with pin-on-disk geometry. After sliding wear tests, the worn surfaces were examined by scanning electron microscopy （SEM） equipped with an energy dispersive X-ray spectrometer （EDS）. Results have shown that the wear mechanism is oxidative and adhesive.
参考文献
| [1] | P.K. Deshpande;R.Y. Lin .Wear resistance of WC particle reinforced copper matrix composites and the effect of porosity[J].Materials Science & Engineering, A. Structural Materials: Properties, Misrostructure and Processing,2006(1/2):137-145. |
| [2] | Z.M. Du;J.P. Li .Study of the preparation of Al203sf SiCp/Al composites and their wear-resisting properties[J].Journal of Materials Processing Technology,2004(1/3):298-301. |
| [3] | Y. Sahin;M. Acilar .Production and properties of SiCp-reinforced aluminium alloy composites[J].Composites, Part A. Applied science and manufacturing,2003(8):709-718. |
| [4] | J. P. Tu;L. Meng;M. S. Liu .Friction and wear behavior of Cu-Fe{sub}3Al powder metallurgical composites in dry sliding[J].Wear: an International Journal on the Science and Technology of Friction, Lubrication and Wear,1998(1):72-79. |
| [5] | C. E. da Costa;W. C. Zapata;F. Velasco;J. M. Ruiz-Prieto;J. M. Torralba .Wear behaviour of aluminum reinforced with nickel aluminide MMCs[J].Journal of Materials Processing Technology,1999(0):66-70. |
| [6] | I. Yasar;A. Canakci;F. Arslan .The effect of brush spring pressure on the wear behaviour of copper-graphite brushes with electrical current[J].Tribology International,2007(9):1381-1386. |
| [7] | S. R. Dong;J. P. Tu;X. B. Zhang .An investigation of the sliding wear behavior of Cu-matrix composite reinforced by carbon nanotubes[J].Materials Science & Engineering, A. Structural Materials: Properties, Misrostructure and Processing,2001(1/2):83-87. |
| [8] | O. Torun;I. Celikyurek .Diffusion bonding of nickel aluminide Ni_(75)Al_(25) using a pure nickel interlayer[J].Intermetallics,2008(3):406-409. |
| [9] | I. Celikyurek;B. Baksan;O. Torun .Boronizing of iron aluminide Fe_(72)Al_(28)[J].Intermetallics,2006(2):136-141. |
| [10] | J. -H. Jin;D. J. Stephenson .The sliding wear behaviour of reactively got pressed nickel aluminizes[J].Wear: an International Journal on the Science and Technology of Friction, Lubrication and Wear,1998(2):200-207. |
| [11] | C. X. Li;J. Xia;H. Dong .Sliding wear of TiAl intermetallics against steel and ceramics of Al{sub}2O{sub}3, Si{sub}3N{sub}4 and WC/Co[J].Wear: an International Journal on the Science and Technology of Friction, Lubrication and Wear,2006(5/6):693-701. |
- 下载量()
- 访问量()
- 您的评分：
-
10%
-
20%
-
30%
-
40%
-
50%