采用CCT-AY-Ⅱ型钢板连续退火机对高强TRIP钢进行热处理,获得铁素体、贝氏体,残留奥氏体和少量马氏体的组织.采用SEM、EBSD等微观方法观察制备的TRIP钢的微观组织,利用XRD法测量了残留奥氏体量,实验测量了其力学性能.结果表明:820℃两相区退火,410℃贝氏体区后实验钢获得良好的综合力学性能,屈服强度达到804 MPa,抗拉强度928 MPa,总伸长率27.55％,强塑积25.57 GPa·％.这主要是退火后实验钢合适的相比例以及一定量残留奥氏体共同作用的结果;实验钢在高速拉伸下,应力随应变的增加而增加,实验钢在高速下表现出良好的力学性能,不仅具有很高的强度,而且表现出良好的塑性,高速下实验钢良好的力学性能是因为钢中大量残留奥氏体发生TRIP效应造成的.
Multiphase microstructure which consists of ferrite,bainite,retained austenite and a few martensitein was obtained in a high strength TRIP steel by interitical annealing and bainite austemping on a CCT-AY-Ⅱ type continuous annealing simulator.Microstructure of the steel was observed by means of SEM and EBSD technique.The amount of retained austenite in the steel was determined by X-ray diffraction and its mechanical properties were measured.The results indicate that the tested steel sheet exhibits good comprehensive properties with yield strength of 804 MPa,tensile strength up to 928 MPa and total elongation A50of 27.55％,and the product of tensile strength and elongation is 25.57 GPa·％,after intercritical annealing at 820 ℃ and bainitic austempering at 410 ℃ due to the refined microstructure,appropriate proportion of phases and a specific proportion of retained austenite.The stress increases with the increase of the strain for the steel under high speed tensile loading,which shows a good combination of shrength and plasticity.The good mechanical performance of the steel under high speed tensile test is ascribed to the TRIP effect of the large amount of residual austenite in the steel
参考文献
| [1] | 康永林;陈贵江;朱国明;宋仁伯.新一代汽车用先进高强钢的成形与应用[J].钢铁,2010(8):1-6,19. |
| [2] | 李楠;时捷;王存宇;赵晖;陈为亮;惠卫军;曹文全.两相区退火时间对冷轧中锰钢组织和力学性能的影响[J].材料热处理学报,2011(8):74-78. |
| [3] | 尹鸿祥;赵爱民;赵征志;李振;黄耀;代乐乐;曹佳丽.退火时间对超细晶中锰TRIP钢组织性能的影响[J].材料热处理学报,2013(9):64-68. |
| [4] | 张志勤;黄维;高真凤.汽车用第3代先进高强度钢的研发进展[J].特殊钢,2013(1):16-21. |
| [5] | 董丹阳;刘杨;王磊;苏亮进.应变速率对DP780钢动态拉伸变形行为的影响[J].金属学报,2013(2):159-166. |
| [6] | Han, HN;Oh, CS;Kim, G;Kwon, O.Design method for TRIP-aided multiphase steel based on a microstructure-based modelling for transformation-induced plasticity and mechanically induced martensitic transformation[J].Materials Science and Engineering. A, Structural Materials: Properties, Microstructure and Processing,20091/2(1/2):462-468. |
| [7] | 范倚;王明林;张慧;陶红标;赵沛;李士琦.第三代汽车钢的热塑性及断裂机理[J].北京科技大学学报,2013(5):607-612. |
| [8] | Georg FROMMEYER;Udo BRUX;Peter NEUMANN.Supra-Ductile and High-Strength Manganese-TRIP/TWIP Steels for High Energy Absorption Purposes[J].ISIJ International,20033(3):438-446. |
| [9] | 李振;赵爱民;唐获;米振莉;焦殿辉.低碳中锰热轧TRIP钢退火工艺及组织演变[J].北京科技大学学报,2012(2):132-136. |
| [10] | Seok-Jae Lee;Seawoong Lee;Bruno C. De Cooman.Mil partitioning during the intercritical annealing of ultrafine-gralned 6% Mn transformation-induced plasticity steel[J].Scripta materialia,20117(7):649-652. |
- 下载量()
- 访问量()
- 您的评分：
-
10%
-
20%
-
30%
-
40%
-
50%