采用SXP-16精密锻造机，分别以920、940、960℃三种不同的热加工温度将φ85 mm的Ti6242S合金棒坯精锻至φ32 mm叶片用小规格棒材。研究了三种不同热加工温度对Ti6242S合金棒材显微组织、力学性能及探伤杂波水平的影响。结果表明：随着热加工温度的提高，初生α相含量降低，等轴化提高；经过相同的热处理制度（980℃×1 h／AC＋595℃×8 h／AC）处理后，三种不同温度热加工的棒材显微组织和力学性能相当；随着热加工温度的提高，棒材的杂波水平提高。
The Ti6242S titanium alloy bars were prepared by SXP-16 precision forging machine from diameter of 85 mm to 32 mm at temperature of 920 ℃, 940 ℃ and 960 ℃.The effects of hot working temperature on microstructure, mechanical properties and flaw detection level of the Ti6242S titanium alloy bars were investigated.The result show that the volume fraction of the primary αphase decreases with the increase of the hot working temperature, but the equiaxial level of αphase is improved.The microstructures and mechanical properties of the bars have little change under the same heat treatment.The flaw detection level of Ti6242S titanium alloy bars raises with the increase of the hot working temperature.
参考文献
| [1] | 脱祥明,彭益群,岳耀峰.Ti-6242S合金在β区的锻造工艺研究[J].稀有金属,2000(04):282-286. |
| [2] | 张喜燕;赵永庆;白晨光.钛合金及应用[M].北京:化学工业出版社,2005 |
| [3] | 脱祥明,岳耀峰,彭益群.热处理对 Ti-6242S 合金显微组织和性能的影响[J].稀有金属,2001(04):315-319. |
| [4] | 付艳艳,宋月清,惠松骁,米绪军.航空用钛合金的研究与应用进展[J].稀有金属,2006(06):850-856. |
| [5] | 娄贯涛.钛合金的研究应用现状及其发展方向[J].钛工业进展,2003(02):9-13. |
| [6] | McBagonluri F;Akpan E;Mercer C;Shen W;Soboyejo WO .An investigation of the effects of microstructure on dwell fatigue crack growth in Ti-6242[J].Materials Science & Engineering, A. Structural Materials: Properties, Misrostructure and Processing,2005(1/2):111-134. |
| [7] | 刘军 .不同热处理制度下Ti6242S及Ti6242显微组织与性能关系的研究[D].西安:西安建筑科技大学,2012. |
| [8] | 黄张洪,曲恒磊,邓超,杨建朝.Ti6242s钛合金锻件的组织和性能[J].热加工工艺,2011(19):124-125. |
| [9] | 田录,吉海宾,雷家峰,张钧.Ti6242s合金本构关系的研究[J].热加工工艺,2013(20):97-99,102. |
| [10] | 王海;刘军 .固溶时效对Ti6242 合金组织性能的影响[J].热加工工艺,2014,43(16):198-200. |
| [11] | 梁佳,于兰兰,毛小南,刘军.时效温度对Ti6242S合金组织与性能的影响[J].铸造技术,2012(07):796-798. |
| [12] | 王琛,毛小南,韩栋,张平祥.热处理对Ti6242S合金组织和性能的影响[J].金属热处理,2012(08):33-35. |
- 下载量()
- 访问量()
- 您的评分：
-
10%
-
20%
-
30%
-
40%
-
50%