欢迎登录材料期刊网

材料期刊网

高级检索

The effect of bainite morphology on mechanical properties of the mixed bainite-martensite microstructure in D6AC low alloy ultra-high strength steel has been studied in the present work. For this purpose, samples austenitized at 910℃ for 40 min were quenched in three different ways. Some of the samples were directly oil-quenched, some others were quenched in salt bath at 330 ℃ and the remaining samples were quenched in salt bath at 425 ℃ for various holding times. All samples were tempered at 200 ℃ for 2 h. Microstructures were examined by optical microscopy (OM) and scanning electron microscopy (SEM). Fracture surfaces also were studied by SEM. Results showed that the mixed microstructure containing martensite and 28 vol.% of the lower bainite exhibited higher yield and tensile strengths than the fully martensitic microstructure. This could be mainly attributed to the partitioning of the prior austenite grains by the lower bainite and enhancing the strength of lower bainite in the mixed microstructure by plastic constraint. Charpy V-notch (CVN) impact energy and ductility were improved by increasing the volume fraction of the lower bainite. This is not the case about the mixed microstructure containing the upper bainite and martensite. As a result, the tensile and CVN impact properties of mixed upper bainite-martensite microstructure are lower than those of the fully martensitic microstructure. Finally, fractography studies showed cleavage fracture at the surface of CVN impact specimens with martensitic and upper bainitic microstructures confirming the tendency to brittle behavior.

参考文献

[1] S. Maropoulos;N. Ridley;S. Karagiannis .Structural variations in heat treated low alloy steel forgings[J].Materials Science & Engineering, A. Structural Materials: Properties, Misrostructure and Processing,2004(1/2):79-92.
[2] A. R. Mirak;M. Nili-Ahmadabadi .Effect of modified heat treatments on the microstructure and mechanical properties of a low alloy high strength steel[J].Materials Science and Technology: MST: A publication of the Institute of Metals,2004(7):897-902.
[3] A. Abdollah-Zadeh;A. Salemi;H. Assadi.Mechanical behavior of CrMo steel with tempered martensite and ferrite–bainite–martensite microstructure[J].Materials Science & Engineering, A. Structural Materials: Properties, Misrostructure and Processing,2008:325-328.
[4] S. A. Sajjadi;S. M. Zebarjad .Isothermal transformation of austenite to bainite in high carbon steels[J].Journal of Materials Processing Technology,2007(1/3):107-113.
[5] R. Bakhtiari;A. Ekrami .The effect of bainite morphology on the mechanical properties of a high bainite dual phase (HBDP) steel[J].Materials Science & Engineering, A. Structural Materials: Properties, Misrostructure and Processing,2009(1/2):159-165.
[6] D.QUIDORT;Y.J.M.BRECHET .ISOTHERMAL GROWTH KINETICS OF BAINITE IN 0.5 percent C STEELS[J].Acta materialia,2001(20):4161-4170.
[7] J. Chakraborty;D. Bhattacharjee;I. Manna .Development of ultrafine bainite + martensite duplex microstructure in SAE 52100 bearing steel by prior cold deformation[J].Scripta materialia,2009(6):604-607.
[8] J. Chakraborty;D. Bhattacharjee;I. Manna .Austempering of bearing steel for improved mechanical properties[J].Scripta materialia,2008(2):247-250.
[9] N. Saeidi;A. Ekrami .Comparison of mechanical properties of martensite/ferrite and bainite/ferritedual phase 4340 steels[J].Materials Science & Engineering, A. Structural Materials: Properties, Misrostructure and Processing,2009(1/2):125-129.
[10] X. Z. ZHANG;J. F. KNOTT .CLEAVAGE FRACTURE IN BAINITIC AND MARTENSITIC MICROSTRUCTURES[J].Acta materialia,1999(12):3483-3495.
上一张 下一张
上一张 下一张
计量
  • 下载量()
  • 访问量()
文章评分
  • 您的评分:
  • 1
    0%
  • 2
    0%
  • 3
    0%
  • 4
    0%
  • 5
    0%