运用fluent 6.3对板坯连铸结晶器进行数值计算,研究结晶器宽度对流场的影响。结果表明：对于230mm厚结晶器,随结晶器宽度增加,其液面的最大水平流速减小,但减小的幅度趋缓,液面最大垂直速度和冲击点处速度逐渐减小;宽度分别为1 400、1 600和2 150mm时,液面水平流速达到最大时分别为距离窄边460、540和750m处,冲击点位置分别距离液面0.37、0.40和0.46m,冲击点的速度分别为5.2、4.4和2.5cm/s。
Slab continuous casting mould was calculated by software fluent 6.3,the effects of mould width on the flow field were investigated.It is concluded that： as for mould of 230mm thickness,as the increase of mould width,maximum horizontal velocity on the level liquid decreases,then approaches to a flat,maximum velocity perpendicular to level liquid and velocity of impact point on the narrow side decrease;when the mould width are 1 400 mm,1 600 mm and 2 150 mm,and the distance to the narrow side are 460 mm,540 mm and 750 mm,horizontal velocity on the level liquid reach the maximum,the impact points on the narrow side are 370 mm,400 mm and 460 mm to the level liquid,and the velocity on the impact point are 5.2 cm·s-1,4.4 cm·s-1 and 2.5 cm·s-1.
参考文献
| [1] | Theodorakakos A;Bergeles G .Numerical Investigation of the Interface in a Continuous Steel Casting Mold Water Model[J].Metallurgical and Materials Transactions B:Process Metallurgy and Materials Processing Science,1998,29(12):1321. |
| [2] | 张大江,陈登福,王翠娜,靳星,谢鑫.不同宽度板坯结晶器内流场的水模型和数值模拟研究[J].特殊钢,2010(01):14-17. |
| [3] | 王浩,王恩刚,康丽,吴莉,周玮.板坯连铸结晶器内钢液流场的数值模拟[J].工业加热,2009(03):54-57. |
| [4] | 韩春鹏,张捷宇,任三兵,范正洁,贺友多.板坯连铸结晶器内钢液流场的数值模拟[J].内蒙古科技大学学报,2008(01):50-53. |
| [5] | 杨春宝,闫小林,陈伟.基于ANSYS的板坯连铸结晶器内流场数值模拟[J].河北理工大学学报(自然科学版),2008(03):34-40. |
| [6] | Brian G. THOMAS;Lifeng ZHANG .Mathematical Modeling of Fluid Flow in Continuous Casting[J].ISIJ International,2001(10):1181-1193. |
| [7] | R. Miranda;M. A. Barron;J. Barreto .Experimental and numerical analysis of the free surface in a water model of a slab continuous casting mold[J].ISIJ International,2005(11):1626-1635. |
| [8] | Brian G. THOMAS;Lifeng ZHANG .Mathematical Modeling of Fluid Flow in Continuous Casting[J].ISIJ International,2001(10):1181-1193. |
- 下载量()
- 访问量()
- 您的评分：
-
10%
-
20%
-
30%
-
40%
-
50%