以航空发动机涡轮叶片常用材料 Inconel718高温镍基合金为基材进行电解加工(ECM)，得到气膜冷却孔。通过几组交叉实验，分析了加工电压、电解液NaNO3含量、工具电极进给速率3个工艺参数对加工过程稳定性、加工精度和加工效率的影响，得到电解加工的最优工艺参数为：电解液中NaNO3的质量分数10%，加工电压10 V，工具电极进给速率7μm/s，电解液流量10 mL/min。在该工艺条件下，加工过程稳定，效率高，精度好。
Film cooling holes were obtained by electrochemical machining (ECM) using Inconel718 nickel-based superalloy commonly used for turbine blade of aero-engine as the substrate. The effects of three process parameters including machining voltage, NaNO3 content in electrolyte, and feed rate of tool electrode on stability, accuracy, and efficiency of the machining process were analyzed through several groups of crossover experiment. The optimal process parameters of electrochemical machining were obtained as follows: mass fraction of NaNO3 in electrolyte 10%, machining voltage 10 V, feed rate of tool electrode 7μm/s, and flow rate of electrolyte 10 mL/min. The process features good stability, high efficiency, and fine precision under the optimal conditions.
参考文献
| [1] | M. S. Hewidy;S. J. Ebeid;T. A. El-Taweel;A. H. Youssef .Modelling the performance of ECM assisted by low frequency vibrations[J].Journal of Materials Processing Technology,2007(1/3):466-472. |
| [2] | Sebastian Skoczypiec .Research on ultrasonically assisted electrochemical machining process[J].The International Journal of Advanced Manufacturing Technology,2011(5/8):565-574. |
| [3] | 王维,朱荻,曲宁松,黄绍服,房晓龙.管电极电解加工工艺过程稳定性研究[J].机械工程学报,2010(11):179-184. |
| [4] | Li Zhiyong,Niu Zongwei.Convergence Analysis of the Numerical Solution for Cathode Design of Aero-engine Blades in Electrochemical Machining[J].中国航空学报(英文版),2007(06):570-576. |
| [5] | 曹国强,刘江宁,李原吉.基于正交试验的微电解加工高温合金的研究[J].天津工业大学学报,2013(05):61-63. |
| [6] | H. T. Lee;T. Y. Tai .Relationship between EDM parameters and surface crack formation[J].Journal of Materials Processing Technology,2003(3):676-683. |
| [7] | Chan Hee Jo;Bo Hyun Kim;Chong Nam Chu .Micro electrochemical machining for complex internal micro features[J].CIRP Annals,2009(1 CD/ROM):181-184. |
| [8] | 范植坚,王岗罡,贾建利.电解加工测试方法的研究进展[J].电加工与模具,2005(05):1-4,11. |
| [9] | BIANCHINI C;FACCHINI B;MANGANI L.Heat transfer performances of fan-shaped film cooling holes:Part II-Numerical analysis[A].,2010:1573-1583. |
| [10] | 王明环,朱荻,张朝阳.微细孔电解加工控制方法及试验研究[J].中国机械工程,2007(06):646-650. |
| [11] | 李兆龙,狄士春.深小孔脉冲电解加工精度控制研究[J].兵工学报,2012(04):414-418. |
| [12] | 曾永彬,张玉冬,房晓龙,曲宁松.盐溶液管电极电解加工钛合金深小孔[J].电加工与模具,2014(02):29-32. |
| [13] | 许斌,邹洪庆.镍磷合金表面电化学蚀刻层的性能表征[J].表面技术,2013(06):18-22. |
| [14] | HUNG J;LIU H;CHANG Y et al.Development of helical electrode insulation layer for electrochemical micro-drilling[J].Procedia CIRP,2013,6:373-377. |
| [15] | 谢文清,朱荻,曲宁松,王维.管电极电解加工监控系统的设计与试验研究[J].机械制造与自动化,2009(04):128-131. |
- 下载量()
- 访问量()
- 您的评分：
-
10%
-
20%
-
30%
-
40%
-
50%