采用粉末冶金法,通过在金属Mo中添加TiH2粉末及超细TiC粉末制备Mo-Ti-TiC合金,研究TiC的添加对Mo-Ti合金的拉伸性能和显微组织的影响.结果表明,TiC的添加使Mo-Ti合金的拉伸强度得到有效提高.TiC添加量在0.05%(质量分数)时,合金拉伸强度最高,强度较Mp-Ti合金提高了31.7%.TiC的添加保护了基体中由TiH2颗粒分解脱氢所形成的单质Ti颗粒,降低其氧化程度.添加TiC后,合金内部生成含元素Mp、Ti、O和C的第二相粒子,有效阻止合金晶粒长大,因此,随着合金中TiC含量的增加,合金的晶粒尺寸减小.
参考文献
| [1] | 曹维成,刘静,任宜霞.掺杂不同微量元素对钼材性能的影响[J].稀有金属快报,2006(08):29-32. |
| [2] | 向铁根.钼冶金[M].长沙:中南工业大学出版社,2002 |
| [3] | Buckman R W Jr .[J].Int Journal of Refractory Metals ＆ Hard Materials,2000,18:253. |
| [4] | 范景莲,成会朝,卢明园,黄伯云,田家敏.微量合金元素Ti、Zr对Mo合金性能和显微组织的影响[J].稀有金属材料与工程,2008(08):1471-1474. |
| [5] | Cockeram BV;Smith RW;Snead LL .Tensile properties and fracture mode of a wrought ODS molybdenum sheet following fast neutron irradiation at temperatures ranging from 300 degrees C to 1000 degrees C[J].Journal of Nuclear Materials: Materials Aspects of Fission and Fusion,2005(2/3):165-184. |
| [6] | Cockeram B V .[J].Materials Science and Engineering A:Structural Materials Properties Microstructure and Processing,2005,418:120. |
| [7] | 卢明园,范景莲,成会朝,刘涛,田家敏,黄伯云.Ti对Mo-Ti合金拉伸强度及显微组织的影响[J].中国有色金属学报,2008(03):409-413. |
| [8] | Fan Jinglian et al.[J].International Journal of Refractory Metals and Hard Materials,2009,27:78. |
| [9] | YUTAKA HIRAOKA;SATORU YOSHIMURA .Low Temperature Fracture Strength and Ductility of Carburized Mo-Ti Alloys[J].International Journal of Refractory Metals & Hard Materials,1995(4):205-210. |
| [10] | Masahiro Nagae;Yoshito Takemoto;Tetsuo Yoshio .Preparation of structurally controlled dilute molybdenum-titanium alloys through a novel multi-step internal nitriding technique and their mechanical properties[J].Materials Science & Engineering, A. Structural Materials: Properties, Misrostructure and Processing,2005(1/2):50-56. |
| [11] | Satoru Yoshimura et al.[J].Int Journal of Refractory Metals ＆ Hard Materials,1996,14(5-6):325. |
| [12] | Takeshi Inoue;Yutaka Hiraoka;Ei-ichi Sukedai .Hardening behavior of dilute Mo-Ti alloys by two-step heat-treatment[J].International Journal of Refractory Metals & Hard Materials,2007(2):138-143. |
| [13] | Kitsunai Y;Kurishita H;Kuwabara T;Narui M;Hasegawa M;Takida T;Takebe K .Radiation embrittlement behavior of fine-grained molybdenum alloy with 0.2 wt% TiC addition[J].Journal of Nuclear Materials: Materials Aspects of Fission and Fusion,2005(2/3):233-243. |
| [14] | Kurishita H et al.[J].Mater:Trans JIM,1989,30:1009. |
| [15] | Myoung Ki Yoo et al.[J].Int Journal of Refractory Metals ＆ Hard Materials,1996,14:355. |
| [16] | Hiroaki Kurishita et al.[J].Journal of Nuclear Materials,1996,233-237:557. |
| [17] | 黄培云.粉冶金属原理[M].北京:冶金工业出版社,2004 |
| [18] | Massalski T B.Binary Alloy Phase Diagrams Second Edition[M].Ohio:ASM International,1986 |
| [19] | Hiroaki Kurishita;Yuji Kitsunai .Development of Molybdenum Alloy with High Toughness at Low Temperatures[J].Materials transactions,1996(1):89-97. |
上一张
下一张
上一张
下一张
计量
- 下载量()
- 访问量()
文章评分
- 您的评分：
-
10%
-
20%
-
30%
-
40%
-
50%