针对编织类纤维增强体的纤维束之间与纤维束内孔隙的双尺度特点,建立了平纹织物的细观结构模型,并推导了汇函数的数学表达式.建立了局部细观流动特征的非饱和流动控制方程,利用有限元/控制体积方法求解,得到了局部饱和度分布.与实验进行比较,吻合较好.
A micro-structure model for the double scale porous media was set up. An mathematical expression of sink function was derived. The governing equation for local unsaturated flow was obtained. The finite element control volume method was employed to simulate the unsaturated flow. Finally, the results from numerical simulations and experiments were compared, which agreed well.
参考文献
| [1] | 张刚翼,沈玉考.浅谈RTM工艺中对树脂流动性的控制[J].玻璃钢/复合材料,1999(5):10-12.Zhang Gangyi,Shen Yukao.Introduction of resin flow control in RTM technology[J].Fiber Reinforced Plastics/Composite,1999(5):10-12. |
| [2] | Dai F H,Du S Y,Zhang B M,et al.A new method to track resin flow fronts in mold filling simulation of RTM process[J].Journal of Materials Science and Technology,2004,20(3):335-340. |
| [3] | Dai F H,Zhang B M,Du S Y.Analysis of upper-and lower-limits of fil time in resin transfer mold filling simulation[J].Journal of Composite Materials,2004,38(13):1115-1136. |
| [4] | 戴福洪,张博明,杜善义.用均匀化方法预报平纹织物的渗透率[J].复合材料学报,2009,26(2):90-93.Dai Fuhong,Zhang Boming,Du Shanyi.Permeability prediction of fabric preform using homogenization method[J].Acta Materiae Compositae Sinica,2009,26(2):90-93. |
| [5] | Hammami A,Gauvin R,Trochu F.Modeling the edge effect in liquid composites molding[J].Applied Science and Manufacturing,1998,29(5):603-609. |
| [6] | Pan R,Liang z Y,Zhang C.Statistical characterization of fiber permeability for composite manufacturing[J].Polymer Composites,2000,21(6):996-1006. |
| [7] | Mahale A D,Prudhomme R K,Rebenfeld L.Quantitative measurement of voids formed during liquid impregnation of non-woven multifilament glass networks using an optical visualization technique[J].Polymer Engineering and Science,1992,32(5):319-326. |
| [8] | Koo Kang Moon,Lee Woo Il,Hahn Thomas H.Formation of microvoids during resin-transfer molding process[J].Composites Science and Technology,2000,60(12/13):2427-2434. |
| [9] | Binetruy C,Hilaire B,Pabiot J.Tow impregnation model and void formation mechanisms during RTM[J].Journal of Composite Materials,1998,32(3):223-245. |
| [10] | Spaid M A,Phelan Jr F R.Modeling void formation dynamics in fibrous porous media with the lattice Boltzmann method[J].Composites Part A,1998,29(7):749-755. |
| [11] | Olivero Kristian A,Barraza Harry J,O'Rear Edgar A.Effect of injection rate and post-fill cure pressure on properties of resin transfer molded disks[J].Journal of Composite Materials,2002,36(16):2011-2028. |
| [12] | Patel N,Rohatgi V,Lee L J.Micro scale flow behavior and void formation mechanism during impregnation through a unidirectional stitched fiberglass mat[J].Polymer Engineering and Science.1995,35(10):837-851. |
| [13] | Rohatgi V,Patel N,Lee L J.Experimental investigation of flow-induced microvoids during impregnation of unidirectional stitched fiberglass mat[J].Polymer Composites,1996,17(2):161-170. |
| [14] | Simacek Pavel,Advani Suresh G.A numerical model to predict fiber tow saturation during liquid composite molding[J].Composites Science and Technology,2003,63(12):1725-1736. |
上一张
下一张
上一张
下一张
计量
- 下载量()
- 访问量()
文章评分
- 您的评分：
-
10%
-
20%
-
30%
-
40%
-
50%