利用显式动力学有限元方法和几何模型更新方法模拟了不同立辊孔型下多道次立-平辊轧制过程,对轧后各道次的轧件头尾形状进行了分析.结果表明:采用平立辊轧制时,轧件影响深度比采用孔型立辊时小,且轧件尾部出现尖角,而采用孔型立辊时未出现;采用孔型辊时,孔型立辊底部导角大小对轧件头尾形状影响较小,且轧件伸长率比采用平立辊时大.同时,平立辊轧制过程头尾情况与用铅实验值吻合较好,说明了本次分析的正确性.
参考文献
| [1] | Okado M;Ariizumi T;Noma Y et al.Width Behavior ofHead and Tail of Slabs at Edge Rolling in Hot Strip Mills[J].Journal of The Iron and Steel Institute of Japan(In Japanese),1981,67(15):2516-2525. |
| [2] | Nikaido H;Naoi T;Shibata K et al.Numerical Simulation of Width Spread of Dog-Bone Slab in Non-Steady Horizontal Rolling[J].J Jpn Soc Technol Plasticity,1984,25(277):129-135. |
| [3] | Chung W K;Choi S K;Thomson P F .Three-Dimensional Simulation of Edge Rolling Process by Explicit Finite-Element Method[J].Journal of Materials Processing Technology,1993,38:85-102. |
| [4] | Xiong Shangwu;Liu Xianghua;Wang Guodong;Zhang Qiang .A three-dimensional finite element simulation of the vertical-horizontal rolling process in the width reduction of slab[J].Journal of Materials Processing Technology,2000(1/3):146-151. |
| [5] | Xiong Shangwu;Zheng Guifang;Liu Xianghua .Analysis of the non-steady state vertical-horizontal rolling process in roughing trains by the three-dimensional finite element method[J].Journal of Materials Processing Technology,2002(1/3):53-61. |
| [6] | XIONG Shang-wu;Rodrigues J M C;Martins P A F .Three-Dimensional Modeling of Vertical-Horizontal Rolling Process[J].Finite Elements in Analysis ans Design,2003,39:1023-1037. |
| [7] | XIONG Shang-wu;LIU Xiang-hua;WANG Guo-dong et al.Simulation of Vertical-Horizontal Rolling Process During Width Reduction by Full Three-Dimensional Rigid-Plastic Finite Element Method[J].Journal of Materials Engineering and Performance,1997,6(06):757-765. |
| [8] | 赵宪明,王国栋,朴海斗,崔承甲.立辊形状对粗轧板坯侧弯的影响[J].东北大学学报(自然科学版),2002(12):1174-1176. |
| [9] | 刘慧,高彩茹,王国栋,刘相华.立辊形状对板坯断面形状的影响[J].塑性工程学报,2003(05):86-88. |
| [10] | 吴迪,赵宪明,董学新,徐震.初轧机无孔型轧制工艺研究及生产应用[J].轧钢,2004(02):1-3. |
上一张
下一张
上一张
下一张
计量
- 下载量()
- 访问量()
文章评分
- 您的评分：
-
10%
-
20%
-
30%
-
40%
-
50%