Z.H. Zou
,
X.M. Yu
,
B.S. Zhang
,
Y. Qi
,
null
,
null
,
null
,
null
,
null
,
null
,
null
,
null
,
null
,
null
,
null
,
null
,
null
金属学报(英文版)
A reactive co-deposition processing for obtaining high-quality single-phase Bi2Sr2Cax-1CuxOy (Bi2212) thin films has been investigated using molecular beam epitaxy (MBE) with 2.7 × 10-3Pa ozone gas introduction for oxidation. The thin films with a constant composition of almost 2 : 2 : 1 : 2 were designed to be fabricated at the substrate temperature between 675 and 780℃, the substrate temperature dependence of the surface morphology and the emergence phases were investigated in detail. A noticeable result is that the distribution of Cu element in the thin films is sensitively changed with the substrate temperature. At 750℃ it is inclined to locate in the periphery of each grain through the diffusion process. At 780℃ the Cu-compositional fluctuation brought around the dendritic crystal growth in the thin films. Below 705℃, the Bi2212 single-phase cannot be achieved in the thin films.
关键词:
Bi2212 (Bi2Sr2Cax-1CuxOy) single-phase
,
null
黄爱华
,
金鸣林
,
李和兴
,
房永征
材料导报
试验是以2种含不同QI的煤沥青为原料,采用变径反应管进行热转化反应制备有序性中间相的研究.试验采用偏光显微镜和扫描电镜(SEM)观察了原料各反应阶段的微观结构,考察了QI对热转化过程中中间相有序生长的影响,分析了热转化过程中软化点及族组分的变化.结果表明:少量的喹啉不溶物含量不会阻碍中间相有序的发展.高QI(2.03%)原料易生成镶嵌结构的中间相体,高温处理后样品呈轴状、短纤维、层片松散的石墨化焦结构;含低QI(0.11%)的原料能生成较好的、大区域的中间相体,域结构的中间相体在外力导向和内部裂解气流的作用下容易生成有序的半焦,高温处理后呈大区域、片层紧密、有序性强的细纤维焦结构.同时研究发现,在热转化过程中可通过测定软化点(SP)和TI含量来确定中间相转化程度.软化点约低于250℃、TI为75%左右时为初始中间相区域体形成阶段、半焦生成的前期.
关键词:
煤沥青
,
热转化反应
,
喹啉不溶物
,
中间相
马宏
,
彭晓东
,
谢卫东
腐蚀学报（英文）
利用对掺法熔铸镁合金AJ61+xY, 研究了合金中相的组成和分布及其在3.5%NaCl溶液中的腐蚀行为. 结果表明, 添加稀土Y使AJ61镁合金的晶粒明显细化,Mg17Al12 相的数量明显减少且由连续网状变成弥散颗粒状分布,沿晶界处生成耐蚀稀土相Al2Y、Al3Y, AJ61镁合金的耐腐蚀性得到明显改善. 耐腐蚀性顺序为:AJ61+1.5%Y>AJ61+2.0%Y>AJ61+1.0%Y>AJ61+0.5%Y.
关键词:
Mg-6Al-1Sr 镁合金
,
yttrium
,
microstructure
,
corrosion resistance
马宏
,
彭晓东
,
谢卫东
腐蚀学报（英文）
利用对掺法熔铸镁合金AJ61++xY,研究了合金中相的组成和分布及其在3.5%NaCl溶液中的腐蚀行为.结果表明,添加稀土Y使AJ61镁合金的晶粒明显细化,Mg17Al12相的数量明显减少且由连续网状变成弥散颗粒状分布,沿晶界处生成耐蚀稀土相Al2Y、Al3Y,AJ61镁合金的耐腐蚀性得到明显改善.耐腐蚀性顺序为:AJ61+1.5%Y＞AJ61+2.0%Y＞AJ61+1.0%Y＞AJ61+0.5%Y.
关键词:
Mg-6Al-1Sr镁合金
,
钇
,
显微组织
,
耐腐蚀
Yan NIU
,
Weitao WU and Chaoliu ZENG (State Key Lab. for Corrosion and Protection
,
Institute of Corrosion and Protection of Metals
,
Chinese Academy of Sciences
,
Shenyang 110015
,
China)F. Gesmundo and F. Viani (Instituto di Chimica
,
Facolta di Ingegneria
,
Un
材料科学技术（英文）
The corrosion of an Fe-based alloy containing 15 wt pct Y in H2-H2S mixtures under 10-3 Pa S2 was studied at 600~800℃ in an attempt to find materials with improved sulphidation resistance with respect to pure Fe. The presence of Y has been shown to be beneflcial, but not sufficient to the level expected. In fact, the alloy is able to form at all tested temperatures an external FeS layer, beneath which a zone containing a mixture of the two sulphides is also present. Thus,Fe can still diffuse through this region to form the outer FeS layer with non-negligible rate. The corrosion rate of Fe is considerably reduced by the Y addition. but the alloy corrodes still much more rapidly than Y. The sulphidation kinetics is generally rather irregular for both the pure metals, while the corrosion rate of the alloy decreases with time and tends to become parabolic after an initial period of 12~17 h. The sulphidation behaviour of the alloys is discussed by taking into account the presence of an intermetallic compound Fe17Y2 and the limited solubility of Y in Fe
关键词:
Transactions of Nonferrous Metals Society of China
The influence of Zr and Y on the cast microstructure of a nickel-based superalloy was investigated by optical microscopy (OM), scanning electron microscopy(SEM), electron probe micro-analysis (EPMA) and X-ray diffraction (XRD). The gamma+gamma' eutectic volume in the superalloy rises notably with the increase of Zr or Y content. Meanwhile, the morphologies of primary MC carbides change from needle and platelet-like to blocky shape with increasing Zr and Y doped. The XRD results show that the primary MC carbide lattice constant increases with Zr and Y additions, and EPMA investigation shows that the platelet-like MC carbides contain primarily Nb and C, while those carbides in blocky shape have 39.2% Zr and 39.6% Nb in average,. These influences on the cast microstructure can be attributed to the atomic size effects of Zr and Y.
关键词:
yttrium;zirconium;carbides;nickel based superalloys;microstructure;solidification;carbide morphology;mechanical-properties;boron;ni3al;yttrium;sulfur
材料科学技术（英文）
The corrosion of an Fe-based alloy containing 15 wt pet Y in H-2-H2S mixtures under 10(-3) Pa S-2 was studied at 600 similar to 800 degrees C in an attempt to find materials with improved sulphidation resistance with respect to pure Fe. The presence of Y has been shown to be beneficial, but not sufficient to the level expected. In fact, the alloy is able to form at all tested temperatures an external FeS layer, beneath which a zone containing a mixture of the two sulphides is also present. Thus, Fe can still diffuse through this region to form the outer FeS layer with non-negligible rate. The corrosion rate of Fe is considerably reduced by the Y addition, but the alloy corrodes still much more rapidly than Y. The sulphidation kinetics is generally rather irregular for both the pure metals, while the corrosion rate of the alloy decreases with time and tends to become parabolic after an initial period of 12 similar to 17 h. The sulphidation behaviour of the alloys is discussed by taking into account the presence of an intermetallic compound Fe17Y2 and the limited solubility of Y in Fe.
关键词:
high-temperature sulfidation;most-reactive component;ni-nb alloys;h2-h2s mixtures;behavior;600-degrees-c-800-degrees-c;oxidation
王永刚
,
何业东
,
朱日彰
中国稀土学报
通过金属蒸汽真空弧离子源(简称MEVVA)方法在Fe3Al表面离子注入Y.在1000°空气中的氧化实验表明,Fe3Al经离子注入Y后,初期氧化速率略有升高,但稳态氧化速率大大降低,氧化膜的塑性和粘附性大大提高,抗氧化性能明显改善.其原因在于注入的Y+在氧化过程中优先氧化,阻碍金属离子向外扩散,促进氧向内传输,改变了氧化膜的形成和生长机制.
关键词:
稀土
,
钇
,
Fe3Al
,
离子注入
,
高温氧化行为
Journal of Materials Research
Based on the best bulk metallic glass (BMG) forming alloy in the Mg-Cu-Y ternary system, we introduced Ag (or Ni) to partially substitute for Cu to improve the glass-forming ability (GFA). The objective of this paper is twofold. First, we illustrate in detail a recently developed search strategy, which was proposed but only briefly outlined in our previous publication [H. Ma, L.L. Shi, J. Xu, Y. Li, and E. Ma: Discovering inch-diameter metallic glasses in three-dimensional composition space. Appl. Phys. Lett. 87, 181915 (2005)]. The protocol to navigate in three-dimensional composition space to land large BMGs is spelled out step-by-step using the pseudo-ternary Mg-(Cu,Ag)-Y as the model system. Second, our ability to locate the best BMG former in the composition tetrahedron allows us to systematically examine, and conclude on, the effects of a given alloying element. The large improvement in glass-forming ability in the Mg-(Cu,Ag)-Y system relative to the based ternary will be contrasted with the reduced glass-forming ability in the Mg-(Cu,Ni)-Y pseudo ternary system. It is demonstrated that the improvement of glass-forming ability requires judicious choice of substitutional alloying elements and concentrations, rather than simple additions of multiple elements assuming the "confusion principle."
关键词:
bulk metallic-glass;shaped copper mold;amorphous-alloys;thermal-stability;ternary-system;casting method;p system;diameter;zr;mm
