Xueshan XIAO
,
Weihuo LI
,
Lei XIA
,
Shoushi FANG
,
Qin HUA
,
Yu
,
a DONG
材料科学技术（英文）
Quasistatic and dynamic tensile behavior of Zr52.5Al10Ni10Cu15Be12.5 bulk amorphous alloy was investigated at the strain rates of 10-4~103 s-1 by using a Shimadzu AG-100KNA autograph and a pneumatic tensile impact tester. It was shown that the tensile fracture strength and the fracture morphology were sensitive to the strain rate. With the increase of the strain rate, the tensile fracture strength decreased and the fracture morphology changed from cleavage into quasi-cleavage, and then into a mixture of microvoid-coalescence dimples and quasi-cleavage veins.
关键词:
Mechanical properties
,
null
,
null
Jiansen NI
,
Hui XU
,
Mingyuan ZHU
,
Qiang LI
,
Bangxin ZHOU
,
Yu
,
a DON
材料科学技术（英文）
Nd8.5Fe74Co5Cu1Nb1Zr3Cr1B6.5 bonded magnets were prepared by melt-spun and subsequent heat treatment. Magnetic properties of Br=0.68 T, JHc=716 kA/m, (BH) max=77 kJ/m3 were achieved. The addition of Cr element shows to be significantly advantageous in reducing grain size and increasing the intrinsic coercivity.
关键词:
null
,
Nanocrystalline
,
Melt-spinning
,
Ma
Yuanzheng YANG
,
Qiaoshen LI
,
Youlan ZHU
,
Xueming MA
,
Yu
,
a DONG
材料科学技术（英文）
Amorphous and nanostructural Fe-B alloys made by mechanical alloying of elemental Fe and amorphous B powders have been studied using X-ray diffraction, differential scanning calorimetry and Mössbauer spectroscopy. It has been shown that the milling conditions have a strong effect on the alloying. The single-phase amorphous alloy, which is limited at nominal composition of Fe60B40, has been produced only by milling in Ar atmosphere and in other composition range the mixture of nanostructure Fe-like phase and Fe2B compound with a little amorphous phase are obtained. While by milling in air atmosphere the introduction of oxygen in air may suppress the formation of amorphous phase, thus the compounds Fe2B may be synthesized with no trace of amorphous phase. The crystallization temperatures of amorphous phase in the resultant products are higher than those of a single amorphous alloy Fe60B40, and hardly independent of the milling conditions and the composition. In addition, it is revealed that detectable B content in the final products is lower than the nominal composition of all the initial samples, which indicates that some B atoms may be located in the disordered interfacial regions of the nanostructural alloyed mixtures.
关键词:
中国腐蚀与防护学报
N。1Atmospheric Corrosivlty for Steels………………………………………………… .LIANG Caideng HO[I i。-tat（6）Caustic Stress Corrosion Cr。king of Alloy 800 Part 2.The Effect of Thiosul执e……………………………………… KONG De-sheng YANG Wu ZHAO Guo-zheng HUANG De.ltL。ZHANG Yu。。he CHEN She。g-bac（13）SERS slid E16CttOCh6iniC81 Stlldy Of Illhibit1Oli M6ch＆tllsth Of ThlollY68 Oil ITOll ID H....
关键词:
王浩
,
刘国权
,
秦湘阁
金属学报
采用Potts模型Monte Carlo方法对3种现存的三维个体晶粒长大速率拓扑依赖性
方程进行了仿真验证. 结果表明, Rivier速率方程认为晶粒
体积变化率dVf/dt与晶粒面数f成线性关系, 与仿真
结果明显不符, 不适用于描述三维晶粒长大过程的动力
学. 当晶粒面数f≥8时, Yu-Liu速率方程和
MacPherson-Srolovitz速率方程均与仿真结果很好吻合,
表明这两者均可以用来定量描述三维晶粒长大过程的动力学；当
f＜8时, 这两个方程均与仿真结果有显著差异.
关键词:
三维晶粒长大
,
topology-dependent grain growth rate equation
王浩
,
刘国权
,
秦湘阁
金属学报
doi:10.3321/j.issn:0412-1961.2008.01.003
采用Potts模型Monte Carlo方法对3种现存的三维个体晶粒长大速率拓扑依赖性方程进行了仿真验证.结果表明,Rivier速率方程认为晶粒体积变化率dVf/dt与晶粒面数,成线性关系,与仿真结果明显不符,不适用于描述三维晶粒长大过程的动力学.当晶粒面数f≥8时,Yu-Liu速率方程和MacPherson-Srolovitz速率方程均与仿真结果很好吻合,表明这两者均可以用来定量描述三维晶粒长大过程的动力学;当f<8时,这两个方程均与仿真结果有显著差异.
关键词:
三维晶粒长大,拓扑依赖性长大速率方程,Potts模型,Monte Carlo仿真
李文琳
,
李章炜
,
幸七四
,
张扬
贵金属
膜片开关用银浆制备使用的有机体系中，树脂、溶剂和添加剂对产品的性能和有害元素控制有重要的意义。经对比实悚，以热塑性聚酯为主体树脂，以MEA混合溶剂为溶剂，以YU-201、硅烷偶联剂以及自制增强塑性材料M-17材料为混合添加剂，制成有机载体。使用该载体制备出的浆料符合膜片开关银浆性能要求，且满足欧盟RoHS指标卤素控制要求。
关键词:
复合材料
,
环保型
,
无卤素
,
膜片开关
,
银浆
