X.L. Xu
,
L. Wang
,
Z. W. Yu and Z.K. Hei(Institute of Metal and Technology
,
Dalian Maritime University
,
Dalian 116024
,
China)
金属学报(英文版)
The cross-sectional microstructure of an ion-nitrided layer on a No.45 steel was studied by transmission electron microscopy (TEM). The results show that the columnar crystals constitute the compound layer. Most of them have the microstructure of alternating ε-Fe2-3N and γ-Fe4N and others are single ε-Fe2-3N phase. There are abnormal strip ferrites between the columnar crystals. The transition layer mainly consists of spherical γ-Fe4N and cementite (Fe3C) particles in the pearlite are dissolved in this layer. In diffusion layer, besides the equilibrium phase γ-Fe4N, there are α -Fe16N2 and the satellite spots around main spots of α-Fe16N2 demonstrate its modulation structure. A metastable ordered cluster zone of the nitropen atoms was found in the division layer.
关键词:
ion nitriding
,
null
,
null
ZANG Qishan LIU Kang Institute of Metal Research
,
Academia Sinica
,
Shenyang
,
ChinaKE Wei ZHENG Yuli Institute of Corrosion and Protection of Metals
,
Academia Sinica
,
Shenyang
,
China
金属学报(英文版)
Investigation was carried out of the crack growth rate in weld metal and heat affected zone (HAZ)of offshore structural steels,homemade steel 36Z together with foreign steel A537 of similar strength grade by comparison,in artificial sea water undergone fatigue with different frequencies.The crack growth rate in weld metal and HAZ of steel 36Z fatigued at low fre- queney may be 3—5 and 4—10 times as high as that at high frequency respectivley.The crack growth rate for steel 36Z may fairly match that of A537,The crack growth model and frac- ture of weld metal in corrosive medium were also discussed.
关键词:
weld metal
,
null
,
null
,
null
,
null
MA Zongyi YAO Zhongkai Harbin Institute of Technology
,
Harbin
,
China
金属学报(英文版)
The SiC_w/Al composite prepared by squeeze casting has a combination of superior room temperature specific strength and modulus together with excellent thermal properties.The extrusion can make an improvement on the strength and ductility of the composite from 582 MPa as squeeze casted up to 639 MPa,and on the transformation from isotropic to the anisotropic structure.This seems to be explained by the orientation of whiskers and the densification of dislocations in matrix.TEM observation indicates that the stacking fault is the usual planar defect on the SiC_w surface. composite;;SiC whisker;;Al alloy;;microstructure
关键词:
composite
,
null
,
null
,
null
郑建邦
,
丁浩
,
郭益平
,
刘林
,
柳伟
,
李行健
金属学报
选用K4169Fe—Ni基高温合金，研究了向熔体中加入NixAlyTiz金属间化合物对合金冷凝后的晶粒尺寸、枝晶组织等凝固组织特征的影响结果表明，加入微量NixAlyTiz细化剂并控制合金液的均匀化处理过程可显著细化晶粒，将铸件整体晶粒细化至0、1—02mm；达到ASTM1—3级,同时、枝晶组织出现了由树枝晶向胞状晶的转变、并且NixAlyTiz细化剂的加入对合金的结晶特性及凝固组织无不良影响.
关键词:
Fe－Ni
,
grain refinement
,
nucleant
,
dendrite morphology
,
null
王晓旭
,
陈利
材料工程
doi:10.3969/j.issn.1001-4381.2011.11.001
通过单根Z-pin从复合材料层合板中拔出的试验方法,测试了Z-pin的拔出强度,计算了Z-pin的临界埋入深度,并引入抗拉强度利用率概念来表征Z-pin的抗拉强度在拔出过程中的利用程度.结果表明,直径0.50mm和0.28mm的Z-pin临界埋入深度分别约为5.1mm和3.1mm.当Z-pin的埋入深度小于临界埋入深度时,Z-pin从层板中拔出；Z-pin拔出强度与埋入深度成正比,与Z-pin的直径成反比；当Z-pin的埋入深度大于临界埋入深度时,Z-pin发生断裂,Z-pin的抗拉强度利用率达到100％.最后提出了提高抗拉强度利用率的建议.
关键词:
Z-pin
,
拔出强度
,
复合材料
,
拔出试验
,
抗拉强度
王晓旭
,
陈利
航空材料学报
doi:10.3969/j.issn.1005-5053.2011.4.017
通过三种复合材料Z-pin的轴向压缩试验,观察了各Z-pin的压缩行为,分析了三种复合材料Z-pin在不同长度时的极限应力及其失效形式.结果表明,直径为0.50mm的碳纤维Z-pin的压缩性能最好,其各长度Z-pin所能承担的极限应力都较大.直径0.28mm的碳纤维Z-pin易发生失稳现象,芳纶纤维Z-pin在压缩力的作用下,接触端容易受到破坏.两种碳纤维Z-pin临界应力的理论值与试验值吻合较好,但芳纶纤维Z-pin的临界应力的试验值比理论值偏低.
关键词:
Z-pin
,
复合材料
,
压缩试验
,
临界应力
Li XING
,
Jie ZHAO
,
Fuzhong SHEN
,
Wei FENG
材料科学技术（英文）
A Z-parameter method is used to evaluate the damage process of HK40 austenitic steel. By using Z-parameter based on the Larson-Miller method, the nonlinear master curve of the log stress vs Larson-Miller parameter P can be expressed as: P=27.74-3.4lgσ-0.032σ, and a family of curves parallel to the master curve can be written as: P=(27.74-Z)-3.4lgσ-0.032σ, where Z represents the magnitude of the deviation from the master curve. According to the creep rupture data both from different segments of a serviced tube and from the same segment locations with different service time, the value of parameter Z has close relationship with the deterioration of creep rupture properties. The damage state of the samples is evaluated by monitoring the changes in natural frequency f and Young0s modulus E, and the relationships between Z and the damage parameters are discussed.
关键词:
Damage evaluation
,
蠕变断裂
,
奥氏体钢
,
Z参数
王军朋
,
李凤
,
敖靖
,
焦丽娜
,
李春梅
,
陈志谦
无机材料学报
doi:10.15541/jim20140463
采用第一性原理计算研究了超硬材料z-BC2N的弹性各向异性性质、应力-应变关系、硬度及最小热导率性质.计算得到的晶体力学行为判据 B/G 为 0.87, 泊松比为 0.084, 普适弹性各向异性指数为 0.09992.[100]晶向上最大拉伸强度达到180 GPa,(100)[010]应变方向上最大剪切强度达到160 GPa,维氏硬度值为77.07 GPa.基于Cahill模型得到的最小热导率为6.811 W/(m·K).结果表明: z-BC2N是脆性材料且力学稳定性良好,有非常高的拉伸强度、剪切强度, 体弹模量为各向同性, 杨氏模量各向异性程度不大.z-BC2N 的最小热导率低于金刚石的最小热导率.
关键词:
超硬材料
,
弹性性质
,
各向异性
,
热导率
詹勇军
,
王锋
,
白黎
,
张素银
,
唐永健
,
吴卫东
,
谌家军
材料导报
以材料非线性光学性质的测试为基础,介绍了原始Z扫描技术的基本原理与数据处理;重点论述了双色时间分辨Z扫描技术的理论,并分析了它在材料光学非线性效应测试中展现的优越性以及应该注意的关键问题.根据Z扫描技术理论和实验的最新研究成果,总结了Z扫描技术的两条发展思路,即:CCD相机代替能量或功率计进行信号的采集和多种改进方法应用于实验测试.
关键词:
Z扫描技术
,
非线性光学效应
,
双色时间分辨Z扫描技术
,
CCD相机
