C.C. Liu
,
Z. Liu and G.X. Chen (Department of Mechanical Engineering
,
Tsinghua University
,
Beijing 100084
,
China)(Department of Mechanical Engineering
,
Tsinghua University
,
Beijing 100084
,
China)(Department of Mechanical Engineering
,
Tsinghua University
,
Beijing 100084
,
China)
金属学报(英文版)
ZBainitic transformation is analyzed in detail according to the factors such as morphology,crystallography,mechanical property of bainite and transformation kinetics,and conclusion is drawn that bainitic transformation is controlled by displacive mechanism and self-fempering of displacive microstructure.That is to say,bainite is the product of such procedure during which undercooled austemite first transforms into one certain displacive microstructure by displacive mechanism and then this microstructure experiences self-fempering.With this idea,several questions,which cannot be illustrated only by displacive transformation mechanism,can be explained successfully.
关键词:
bainitic transformation
,
null
,
null
C.C. Liu
,
K.F. Yao
金属学报(英文版)
Based on the assumptions of parabolic variation of nucleation rate versus time andtransformation kinetics depending mainly on nucleation rate, a different model forbainitic transformation kinetics in hypoeutectoid steels was established. And this modelwas proved to be effective in the description of bainitic transformation by comparisonwith the result of conventional Avrami equation.
关键词:
bainitic transformation kinetics
,
null
,
null
Author S.R. Zhou
,
S.R. Qiao
,
S.H. Bai and C.S. Tian Faculty 401
,
Northwestern Polytechnical University
,
Xian 710072
,
ChinaManuscript received 18 October 1998
金属学报(英文版)
The tensile properties of three different carbonfiberreinforced carbon composites (C/C), mat C/C, 2D laminate and 4D C/C, were investigated under the combined influence of temperature and loading rate. From the experiments the following could be concluded: loading rate between 10-1-10 mm/min was valid; the fracture stress of the three kinds of C/C composites increased with increasing temperature in the range from room temperature to 1900, and the initial modulus of 2D laminate C/C composites increased with the increase of temperature up to 2000.
关键词:
tensile testing
,
null
,
null
,
null
孙乐
,
方向青
,
孟广慧
材料科学与工程学报
doi:10.14136/j.cnki.issn 1673-2812.2016.05.027
通过化学气相渗透(CVI)、树脂浸渍/碳化(I/C)的工艺制成多孔的C/C预制件,采用气体压力浸渗方法向预制体中渗入铜,制备出C/C-Cu复合材料.以高密度C/C复合材料(1.9g/cm3)作为对比样,在MM-200型磨损试验机上对其摩擦磨损性能进行测试,并对其微观结构和摩擦磨损机理进行分析.研究结果表明:C/C-Cu的摩擦系数比C/C复合材料的低,这主要与摩擦表面的摩擦膜有关,铜在摩擦力带动下填充摩擦表面的凹坑,并与碳材料共同形成摩擦膜,摩擦膜的碳含量越高,润滑效果越好.当C/C预制件密度为1.59 g/cm3时,C/C-Cu的摩擦系数和磨损量均小于C/C复合材料,摩擦磨损性能良好.
关键词:
C/C-Cu
,
摩擦磨损
,
摩擦膜
Physical Review B
We report the electronic transport properties of a composite system comprising zero dimensional superconducting NbC(C) nanocapsules and carbon nanofiber matrix. DC susceptibility measurements of the nanocomposite indicate that the critical temperature (T-C) of NbC nanocrystals is 10.7 K. The temperature dependence of electrical resistivity of the specimen pellet follows the Mott's T-1/4 law in a temperature range between T-C of NbC and 300 K, owing to a strong degree of structural disorder in the carbon matrix. Below the T-C of NbC, when the change of its electrostatic energy Delta E is far greater than the thermal energy, an electron will be localized on an isolated NbC nanocrystal at very low temperatures, leading to "Coulomb Blockade." As a result, a collective behavior of the single-electron tunneling effect takes place in a three-dimensional granular superconductors' network composed of the NbC/carbon/NbC tunneling junctions. The superconducting gap of NbC crystals is not found in the current-voltage curves, due to the suppression of surface superconductivity through the contact between NbC and carbon shells.
关键词:
zero-dimensional superconductor;granular metal-films;particles;conduction;nanocapsules;percolation;samples
材料科学技术（英文）
Oxidation behavior of C/C-SiC gradient matrix composites and C/C composites were compared in stationary air. The results show that oxidation threshold of C-SiC materials increases with the amount of SiC particles in the codeposition matrix. Oxidation rate of C/C-SiC gradient matrix composites is significantly lower than that of C/C material. The micro-oxidation process was observed by SEM.
关键词:
carbon carbon composites
Jingyi DENG
,
Wenchuan LIU
,
Haifeng DU
,
Huiming CHEN
,
Yiyi LI
材料科学技术（英文）
Oxidation behavior of C/C-SiC gradient matrix composites and C/C composites were compared in stationary air. The results show that oxidation threshold of C-SiC materials increases with the amount of SiC particles in the codeposition matrix. Oxidation rate of C/C-SiC gradient matrix composites is significantly lower than that of C/C material. The micro-oxidation process was observed by SEM.
关键词:
李波
,
崔园园
,
李爱军
,
周春节
,
张家宝
,
白瑞成
上海金属
综述了C/C-SiC摩擦材料的研究现状,以及C/C-SiC摩擦材料的发展历程.详细分析C/C-SiC摩擦材料的摩擦磨损性能影响因素及机理,介绍了C/C-SiC摩擦材料的改性及应用现状,并对未来的研究重点进行了展望.
关键词:
C/C-SiC摩擦材料
,
摩擦磨损性能
,
机理
,
改性
