DENG Anyuan
,
WANG Engang
,
XU Yongyi
,
ZHANG Xingwu
,
HE Jicheng
钢铁研究学报(英文版)
The free surface waves of a molten lowmelting point Sn32%Pb52%Bi alloy under the imposition of an AC and a static magnetic field were visualized and recorded by use of a laser displacement sensor and a high speed video camera. The Fourier analysis method was used to analyze the oscillation characteristics. The results show that at the center of the free surface, the azimuthal and radial oscillation mode can be found simultaneously owing to AC magnetic field. With increasing coil current intensity, the amplitude and the main frequencies of the oscillations increase, and the azimuthal fluctuation at the center of the free surface is also enhanced. The fluctuation characteristics are closely related to the turbulent flow induced by the alternating electromagnetic force. A series of regular traveling waves can be observed on free surface, and the main frequencies of oscillations at threephase points decrease owing to superposing AC and static magnetic field. The static magnetic field can remarkably control the unstable swinging behavior of free surface. With increasing static magnetic flux density, the amplitude of oscillations at the center of free surface decreases firstly, and then increases, but the fluctuation amplitude at the triplephase point always reduces and keeps within 1 mm, and the azimuthal waves at the center of free surface are weakened. Especially at 144 T, the radial waves are dominant. The static magnetic flux density should be controlled in an appropriate range to obtain more stable free surface. With compound magnetic field, even if the static magnetic flux density is above 10 T, the free surface still vibrates with lower amplitude and dominant frequency.
关键词:
continuous casting
,
compound magnetic field
,
free surface
,
fluctuation
DENG Anyuan
,
WANG Engang
,
HE Jicheng
钢铁研究学报(英文版)
To design a power source system and mold for electromagnetic softcontact continuous casting process and to theoretically estimate the heat losses from the charges and the system power, the effect of structure parameters on system power and magnetic flux density distribution was calculated using finite element method. The results show that as for electromagnetic softcontact continuous casting system with partialsegment type mold, the power consumption is much more than that with a fullsegment type mold; about 62% of electric power is dissipated in the mold, and the effective acting range of magnetic field is relatively narrow. Optimizing mold structure is a crucial measure of remarkably reducing mold power consumption and saving electric energy. Increasing slit number, width, and length can remarkably increase the magnetic flux density in the mold and can reduce the electric energy consumption. Among structure parameters, slit number and slit width are relatively more effective to reduce energy consumption. For a round billet electromagnetic continuous casting system with diameter of 178 mm, the reasonable slit number, width, and length are about 24-32, 05-10 mm, and 160 mm, respectively.
关键词:
continuous casting;softcontact mold;electromagnetic field;electric power;structure parameter
佟媛媛
,
华勤
上海金属
doi:10.3969/j.issn.1001-7208.2010.03.011
运用热分析技术研究了冷却曲线特征值与319铝合金中化学成分之间的关系,并进行回归分析.结果表明,在不考虑工艺因素的情况下,试样的硅含量与α-Al枝晶生长回升温度TαDENG之间的相关性最大,相关系数r为-0.65,以硅含量可预测α-Al枝晶生长回升温度.在浇注过程中,冷却速度与α-Al枝晶生长回升温度TαDENG密切相关,相关系数为r=-0.72.在相同的冷却条件下,铝合金的浇注温度和浇注量对冷却速度有明显的影响,因此,可以通过调整浇注温度和浇注量,控制铝合金的冷却速度,进而也可预测铝合金中α-Al枝晶生长回升温度TαDENG.
关键词:
319铝合金
,
热分析
,
特征值
,
浇注工艺
Transactions of Nonferrous Metals Society of China
A new process for the hydrometallurgy of refractory gold concentrates was presented. The process comprises grinding-leaching, intensified alkaline leaching (IAL), cyanidation and adsorption. In a stirring-type pulverizing-leaching tower mill, the concentrate is ground to <35. 6 μm of 95. 5 % while simultaneously leached by NaOH of 12 kg/t, then carried out intensified alkaline leaching for 48 h by NaOH of 108 kg/t in enhanced agitation tanks with the pulp concentration of 40% solids at the environmental temperature of 9. 5 &SIM; 13. 5 &DEG;C and the environmental pressure of 10(5) Pa. The oxidation rate of As is 94. 9%, and 47. 6% for S. The total consumption of NaOH is only 20% of that theoretically calculated under the conditions of full oxidation at the same oxidation rates of arsenic to arsenate and sulfur to sulfate. The gold leaching rate by NaCN in 24 h is increased from 9. 2% before pretreatment to 94. 2%. The consumption of NaCN is 7. 5 kg/t, which is one times less than that before pretreatment. The extraction cost of gold is about 422 Yuan/t.
关键词:
refractory gold concentrates;grinding-leaching;intensified alkaline;leaching (IAL);pretreatment;common temperature and pressure
Journal of Applied Physics
Motivated by the recent experimental fabrication of half-metallic MnSb and CrSb thin films with metastable zinc-blende structure [Aldous et al. Phys. Rev. B 85, 060403(R) (2012); Deng et al. J. Appl. Phys. 99, 093902 (2006)], we investigate the structural, electronic, and magnetic properties of TiSb in both ground-state NiAs and metastable zinc-blende phases by using the first-principles calculations. It is shown that the ground-state NiAs phase is metallic and nonmagnetic, but the metastable zinc-blende phase exhibits half-metallic ferromagnetism with a magnetic moment of 1.00 mu(B) per formula unit. We also reveal that the half-metallicity in bulk ZB TiSb is lost at the Sb-terminated (001) surface due to the appearance of surface states within the gap of the minority-spin channel, but the Ti-terminated (001) surface retains the bulk half-metallicity, which makes ZB TiSb a promising candidate for the possible epitaxial growth of half-metallic thin films or multilayers on semiconductor substrates for spintronic applications. (C) 2012 American Institute of Physics. [http://dx.doi.org/10.1063/1.4739744]
关键词:
room-temperature ferromagnetism;molecular-beam epitaxy;crsb;cras;spintronics;state;mnas
