ZHAO Zhiyi
,
XIE Jianxin
,
HE Xiaoming
,
DONG Kai
,
YU Yong
,
PAN Feng
钢铁研究学报(英文版)
In the process of steel tube production, continuous tube rolling is the foremost forming procedure and the critical step that decides the dimension precision and the surface quality. In the actual production of the 140 mm full floating mandrel mill in Steel Tube Branch in Baosteel, steel T91 was chosen to be the typical sample, selfmade rolling force transducer and mandrel velocity testing equipment were used, and a series of comprehensive tests on rolling parameters including the rolling force and mandrel velocity were carried out. After the experiment, the friction state between rolling tube and mandrel was analyzed. The friction coefficient was calculated and the values of 0033-0074 in each mill were obtained. The friction coefficient increases obviously along the rolling direction.
关键词:
continuous tube rolling;rolling force;mandrel velocity;friction coefficient
HE Chun-lai
,
ZHU Rong
,
DONG Kai
,
QIU Yong-quan
,
SUN Kai-ming
钢铁研究学报(英文版)
A transient three-dimensional mathematical model has been developed to analyze the three-phase flow in a 150 t EAF (electric arc furnace) using oxygen. VOF (multiphase volume of fluid) method is used to simulate the behaviors of molten steel and slag. Numerical simulation was conducted to clarify the transient phenomena of oxygen impingement on molten bath. When oxygen jet impinges on the surface of molten bath, the slag layer is broken and the penetrated cavity in molten steel is created. Simultaneously, the wave is formed at the surface of uncovered steel on which the slag layer is pushed away by jet. The result of numerical simulations shows that the area and velocity of uncovered steel created by impingement, jet penetration depth change from 0.10 m2, 0.0125 m/s, 3.58 cm to 0.72 m2, 0.1445 m/s, 11.21 cm, when the flow rate of an oxygen lance varies from 500 to 2000 m3/h. The results have been validated against water model experiments. More specially, the relation between the penetration depth and oxygen flow rate predicted by numerical simulation has been found to agree well with that concluded by water model.
关键词:
electric arc furnace
,
three-phase flow
,
numerical simulation
陶明慧
,
张星祥
,
张宇
,
任建岳
,
李新娥
液晶与显示
doi:10.3788/YJYXS20112601.0105
针对某航空相机的设计要求,提出了一种可行的多模式驱动时序设计方法.采用柯达公司的KAI-2093行间转移型面阵CCD传感器.结合它的结构特点和双通道数据传输的思想分析了传感器驱动时序关系,提出了3种驱动模式:binning、no-binning和TDI模式.以Ahera公司的FPGA芯片EP1C6Q240作为时序发生器并实现数据的缓存和拼接,从而实现了时序发生器与数据处理器的一体化设计.在QUARTUSII7.0开发环境下采用VHDL语言编程,通过Modelsim AE6.1b实现数据缓存器的仿真.实测结果表明,所设计的驱动时序满足KAI-2093的时序要求,binning模式下帧频可达60帧/s,120帧/s等,满足高速跟踪要求;no-binning模式下全帧输出帧频可达30帧/s;TDI模式下能保证CCD长时间工作而不影响成像质量,该没计方法提高了系统的集成度和抗干扰能力.
关键词:
航空相机
,
binning模式
,
TDI模式
,
数据缓存
,
数据拼接
,
FPGA
Physical Review B
In a recent publication [S. Dong et al., Phys. Rev. Lett. 103, 127201 (2009)], two (related) mechanisms were proposed to understand the intrinsic exchange bias present in oxides heterostructures involving G-type antiferromagnetic perovskites. The first mechanism is driven by the Dzyaloshinskii-Moriya interaction, which is a spin-orbit coupling effect. The second is induced by the ferroelectric polarization, and it is only active in heterostructures involving multiferroics. Using the SrRuO(3)/SrMnO(3) superlattice as a model system, density-functional calculations are here performed to verify the two proposals. This proof-of-principle calculation provides convincing evidence that qualitatively supports both proposals.
关键词:
thin-films;weak ferromagnetism;superlattices;anisotropy;bifeo3;srruo3;model
