WANG Xiao-nan
,
DI Hong-shuang
,
ZHANG Chi
,
DU Lin-xiu
,
DONG Xue-xin
钢铁研究学报(英文版)
CO2-shielded welding experiments of newly developed, 780 MPa super-high strength heavy-duty truck crossbeam steel were conducted, and the microstructure, microhardness, mechanical properties, and impact toughness of the welded joint were studied. The evolution of the microstructure of the welded joint occurred as follows: welding seam (acicular ferrite+proeutectoid ferrite)→fusion zone (granular bainite-long strip M/A island)→coarse grain zone (granular bainite-long strip or short bar M/A island)→fine grain zone (ferrite+pearlite+blocky M/A island)→mixed grained zone (ferrite+granular bainite+blocky M/A island)→base metal (proeutectoid ferrite+granular bainite-blocky or granular M/A island). Increasing the density of the grain boundaries can effectively improve the impact toughness, and the blocky M/A island hindered crack propagation more effectively than the long strip M/A island. The new hot-rolled 780 MPa super-high strength steel had excellent weldability. The welding technology was applied under the following conditions: welding voltage was 20 to 21 V, welding current was 200 to 210 A, and the gas flow rate was 25 L/min.
关键词:
super-high strength steel
,
crossbeam steel
,
weldability
,
M/A island
,
impact toughness
ZHOU Min
,
DU Lin-xiu
,
LIU Xiang-hua
钢铁研究学报(英文版)
The variation of heat treatments including directed quenching and tempering off-line after controlled rolling (DQT) and quenching off-line and tempering off-line after controlled rolling (RQT) with microstructure and mechanical properties of a low-carbon microalloyed steel was compared and analyzed. For DQT, the quenched steel was obviously banded microstructure, with increasing tempering temperature, lath martensite coarsened, the cusp carbide precipitated at grain boundaries, the yield strength fluctuated slightly, and the fracture-separation was obvious. The impact toughness was better in the steel tempered at 500 ℃ for 1 h. In RQT, with increasing tempering temperature, lath martensite degenerated, intragranular and intergranular finer precipitations with smaller than 30 nm precipitated and grew up and were distributed dispersedly, the stripe-like carbides were distributed at grain boundaries, and the yield strength and tensile strengthen decreased obviously. The impact toughness of RQT process was much better than that of DQT process, and the comprehensive mechanical properties were better for the steel tempered at 500 ℃ for 1 h of RQT process.
关键词:
X120 pipeline steel
,
heat treatment
,
microstructure
,
mechanical property
,
fracture-separation
严东旭
,
刘天伟
,
龙重
,
白彬
,
张鹏程
,
黄河
,
郎定木
,
王晓红
,
朱建国
材料保护
采用单一的表面改性技术难以提高贫铀钛合金(Du-Ti)的耐蚀性能.采用等离子体浸没离子注入技术依次在Du-Ti合金表面注入N和Ti,再利用非平衡脉冲磁控溅射技术制备多层Ti/,TiN,研究了膜层的形貌、结构及耐蚀性能.结果表明:膜层厚约3μm,呈柱状结构,致密,但存在一些微缺陷,膜基结合紧密;膜层出现面心立方结构的TiN和密排六方的Ti,在DU-Ti合金界面形成了少量的UO2,没有铀的氮化物;膜层耐蚀性能较基体得到较大提高;微观缺陷是TiN层局部片状脱落的主要原因,外层TiN出现片状脱落后.注入层和内层Ti/TiN多层膜仍能有效保护基体.
关键词:
等离子体浸没离子注入
,
非平衡磁控溅射
,
复合膜
,
DU-Ti合金
,
电化学腐蚀
,
耐蚀性
刘欣艳
,
赵煜娟
,
夏定国
功能材料
LiNi0.8Co0.2O2是锂离子电池界公认的最有希望取代商业化正极材料LiCoO2的新型正极材料之一.本文所研究的复合正极材料LiNi0.8Co0.2O2是由细小的晶粒构成的球形颗粒,单一相,属于R3m空间群.对复合材料LiNi0.8Co0.2O2的Co-K和Ni-K的XANES分析可知,在600～850℃范围温度对于钴元素的影响不明显,而对于镍元素的影响比较显著,随着Ni-K边位置向高能量移动LiNi0.8Co0.2O2正极材料的放电容量升高.复合材料LiNi0.8Co0.2O2和LiNiO2的Ni-K边XANES相似,表明少量钴的引入对晶体结构的改变不是太多,但是峰的强度较高和峰的位置向高能量移动,表明钴Co对Ni的局域结构进行了调制.
关键词:
LiNi0.8Co0.2O2
,
XANES
,
正极材料
,
局域结构
李星星
,
杨科
,
张磊
,
刘强
工程热物理学报
本文提出了风力机翼型完整的性能参数体系和相应的评估方法,并以此评估了CAS-W1翼型与DU翼型的性能特征.对翼型性能的评估侧重于失速特性、非设计点特性和翼型气动性能的稳定性.评估结果表明,相对于DU翼型,CAS-W1翼型系列设计点性能和非设计点性能较好,但是失速特性和性能稳定性需要优化.
关键词:
风力机专用翼型
,
气动性能评价
,
失速特性
,
稳定性参数
欧阳艳东
,
黄翀
,
余云鹏
,
林舜辉
功能材料与器件学报
doi:10.3969/j.issn.1007-4252.2003.04.020
通过测量ITO玻璃及偏光片对各波段紫外光的光谱特性,分析比较一般偏光片和防紫外偏光片F1225DU的紫外透射光谱,从而说明新型偏光片的防紫外特性.F1225DU对紫外线有比较好的吸收,能挡住各种波长的紫外光,起防止紫外光破坏液晶显示器件的作用.
关键词:
偏光片
,
紫外光
,
液晶显示器
,
透射光谱
蒋兴元
,
魏季和
,
温丽娟
,
李波
上海金属
doi:10.3969/j.issn.1001-7208.2007.02.008
在几何相似比为1∶4的水模型上研究了150t RH装置内钢液的流动和混合特性及吹气管直径的影响.模型的吹气管内径分别为0.10、0.15和0.2 cm.所得结果表明,该装置的环流量计算式为:Qlp＝0.0291Qg0.323Du0.65Dd0.84(t/min),式中Qg-提升气体流量, Nl/min;Du和Dd-上升管和下降管内径,cm.在给定的Qg、Du和Dd下,吹气管直径din的变化对液体的流态没有显著影响,环流量则略有改变,在(0.40～0.80)cm的范围内,Qlp＝0.0304Qg0.322Du0.651Dd0.839din0.07.在Du和Dd均为53 cm、din为0.60 cm的情况下,该装置内钢液的最大("饱和")环流量约为135.1 t/min,相应的Qg为2500 Nl/min.钢包内钢液的混合效果随Qg的增大迅速提高.增大din使混合时间τm(s)略有缩短,对应于0.10,0.15和0.20 cm的孔径,τm与搅拌功率密度ε(W/t)的关系分别为:τm ∞ε-0.497,τm ∞ε-0.493和Tm∞ε-0.476.
关键词:
150t RH装置
,
水模型
,
流动特性
,
混合特性
,
物理模拟
,
吹气管直径
张磊
,
杨科
,
徐建中
,
张明明
,
白井艳
工程热物理学报
钝尾缘翼型气动特性受到尾涡脱落的影响,在翼型DU 91-W2-250的基础上对称加厚得到了新钝尾缘翼氆DU91-W2-250_6,利用密网格进行了非定常气动特性的数值研究.在各个攻角下钝尾缘翼型气动特性都具有周期性的特点,具体的波动特征如波动幅值及周期等则受脱落涡的大小、脱落位置及尾迹宽度的影响,而升力系数波峰、波谷则分别出现在顺时针涡及逆时针涡脱落的时刻.
关键词:
翼型
,
钝尾缘
,
非定常
吴运军
,
张武
,
马怀柱
稀土
doi:10.3969/j.issn.1004-0277.2003.06.004
采用Schlenk技术,在干燥纯氩气保护下,用无水三氯化稀土LnCl3与2-苯基茚以1∶2的摩尔比在THF中反应,得到8种新配合物:(2-ph-Ind)2LnCl (A)[Ln=La(1), Pr(2), Nd(3), Sm(4), Gd(5), Dy(6), Yb(7), Y(8)].再用(A)和LiN(TMS)2在THF中反应,得到两种新的二(2-苯基茚)稀土有机配合物:(2-ph-Ind)2LnN(TMS)2 (B)[Ln=Y(1), Sm(2)].所有配合物都经元素分析、红外和质谱鉴定.配合物(B)在甲基丙烯酸甲酯(MMA)的聚合反应中显示出一定的活性.
关键词:
稀土合成
,
配合物
,
聚合
,
2-苯基茚
