严东旭
,
刘天伟
,
龙重
,
白彬
,
张鹏程
,
黄河
,
郎定木
,
王晓红
,
朱建国
材料保护
采用单一的表面改性技术难以提高贫铀钛合金(Du-Ti)的耐蚀性能.采用等离子体浸没离子注入技术依次在Du-Ti合金表面注入N和Ti,再利用非平衡脉冲磁控溅射技术制备多层Ti/,TiN,研究了膜层的形貌、结构及耐蚀性能.结果表明:膜层厚约3μm,呈柱状结构,致密,但存在一些微缺陷,膜基结合紧密;膜层出现面心立方结构的TiN和密排六方的Ti,在DU-Ti合金界面形成了少量的UO2,没有铀的氮化物;膜层耐蚀性能较基体得到较大提高;微观缺陷是TiN层局部片状脱落的主要原因,外层TiN出现片状脱落后.注入层和内层Ti/TiN多层膜仍能有效保护基体.
关键词:
等离子体浸没离子注入
,
非平衡磁控溅射
,
复合膜
,
DU-Ti合金
,
电化学腐蚀
,
耐蚀性
LIN Jialiu ZHU Shigen YU Zhenzong Tsinghua University
,
Beijing
,
China
金属学报(英文版)
The stress-strain relation for cast low alloy carbon steel at solidification temperature has been examined by the authors' own desingned apparatus for rheological properties measurement.The rheology model,the stress-strain constitutive equation and the rheological parameters therefrom of the cast steel were proposed.Thus the theoretical basis and calcula- ting data for computerized s#nulation on the stress-strain relation and thermal cracking of the cast steel were suggested.
关键词:
rheological behaviour
,
null
,
null
,
null
,
null
李星星
,
杨科
,
张磊
,
刘强
工程热物理学报
本文提出了风力机翼型完整的性能参数体系和相应的评估方法,并以此评估了CAS-W1翼型与DU翼型的性能特征.对翼型性能的评估侧重于失速特性、非设计点特性和翼型气动性能的稳定性.评估结果表明,相对于DU翼型,CAS-W1翼型系列设计点性能和非设计点性能较好,但是失速特性和性能稳定性需要优化.
关键词:
风力机专用翼型
,
气动性能评价
,
失速特性
,
稳定性参数
欧阳艳东
,
黄翀
,
余云鹏
,
林舜辉
功能材料与器件学报
doi:10.3969/j.issn.1007-4252.2003.04.020
通过测量ITO玻璃及偏光片对各波段紫外光的光谱特性,分析比较一般偏光片和防紫外偏光片F1225DU的紫外透射光谱,从而说明新型偏光片的防紫外特性.F1225DU对紫外线有比较好的吸收,能挡住各种波长的紫外光,起防止紫外光破坏液晶显示器件的作用.
关键词:
偏光片
,
紫外光
,
液晶显示器
,
透射光谱
蒋兴元
,
魏季和
,
温丽娟
,
李波
上海金属
doi:10.3969/j.issn.1001-7208.2007.02.008
在几何相似比为1∶4的水模型上研究了150t RH装置内钢液的流动和混合特性及吹气管直径的影响.模型的吹气管内径分别为0.10、0.15和0.2 cm.所得结果表明,该装置的环流量计算式为:Qlp＝0.0291Qg0.323Du0.65Dd0.84(t/min),式中Qg-提升气体流量, Nl/min;Du和Dd-上升管和下降管内径,cm.在给定的Qg、Du和Dd下,吹气管直径din的变化对液体的流态没有显著影响,环流量则略有改变,在(0.40～0.80)cm的范围内,Qlp＝0.0304Qg0.322Du0.651Dd0.839din0.07.在Du和Dd均为53 cm、din为0.60 cm的情况下,该装置内钢液的最大("饱和")环流量约为135.1 t/min,相应的Qg为2500 Nl/min.钢包内钢液的混合效果随Qg的增大迅速提高.增大din使混合时间τm(s)略有缩短,对应于0.10,0.15和0.20 cm的孔径,τm与搅拌功率密度ε(W/t)的关系分别为:τm ∞ε-0.497,τm ∞ε-0.493和Tm∞ε-0.476.
关键词:
150t RH装置
,
水模型
,
流动特性
,
混合特性
,
物理模拟
,
吹气管直径
JIANG Laizhu CUI Kun Huazhong University of Science and Technology
,
Wuhan
,
China
金属学报(英文版)
Studies were made of the calculation of fractal dimension of transverse impact fracture sur- face,and of the correlation between impact toughness of steel and parameters of free-cutting phase by means of the developed fractal geometry model of crack propagation.It is believed that the area fraction,f,of free-cutting phase is negligibly influential to the longitudinal im- pact toughness,as f1 .While the aspect ratio,saying ratio of length to width,of free-cut. ting phase is inversely influential to the transverse impact toughness.This may .be the reason why the transverse impact toughness of free-cutting steel containing more rare earth contrast to sulphur is even higher than the low sulphur containing steel.
关键词:
fractal geometry
,
null
,
null
Liu Zhengyi Fu Jian Zhuang Yuzhi South China University of Technology
,
Guangzhou
,
China Correspondent:LIU Zhengyi professor
,
Dept.of Mechanical Engineering No.2
,
South China University of Technology
,
Guangzhou
,
China
金属学报(英文版)
The nature of“white layer”found in 55SiMnMo steel subjected to friction test has been stu- died using TEM,SEM,X-ray diffraction and EPMA techniques.It is shown that the struc- ture of the“white laver”on the rubbing surface is duplex,consisting of a special martensite and some austenite.This layer may be 25—50 μm thick.It is ultrafine,with grain diametric approximately 30 nm.Its micro-hardness may be as high as Hm 1500 and is capable of cut- ting glass.It has superb corrosion resistance and resists tempering.Its mierostructure and hardness undergo changes only when the steel is tempered above 500℃.
关键词:
friction
,
null
,
null
张磊
,
杨科
,
徐建中
,
张明明
,
白井艳
工程热物理学报
钝尾缘翼型气动特性受到尾涡脱落的影响,在翼型DU 91-W2-250的基础上对称加厚得到了新钝尾缘翼氆DU91-W2-250_6,利用密网格进行了非定常气动特性的数值研究.在各个攻角下钝尾缘翼型气动特性都具有周期性的特点,具体的波动特征如波动幅值及周期等则受脱落涡的大小、脱落位置及尾迹宽度的影响,而升力系数波峰、波谷则分别出现在顺时针涡及逆时针涡脱落的时刻.
关键词:
翼型
,
钝尾缘
,
非定常
