F.M.Yang
,
X.F.Sun
,
H.R.Guan
,
Z.Q.Hu
金属学报(英文版)
The dynamic strain aging behavior during tensile tests of K40S alloy has been investigated in the temperature range of 25-1100℃ with the strain rate range from 10^-4 to 10^-3s^-1. The results show that four different types of serration, identified as A,B, C and E type serration were observed in the temperature range of 300-500℃. The strain exponents for onset of the serrated flow were calculated as 1.21, 2. 79 and 1.61,and the activation energies as 121, 40 and 67kJ/mol for E, B and C type serration respectively. The main mechanism for dynamic strain aging discussed in light of the strain exponent and the activation energy.
关键词:
dynamic strain aging
,
null
,
null
YANG Ying
,
YAN Qing-zhi
,
GE Chang-chun
钢铁研究学报(英文版)
Modified CNS-Ⅱ F/M steel was designed for in-core components of supercritical water cooled reactor. Study on the hot deformation behavior of modified CNS-Ⅱ F/M steel is of great importance for processing parameter planning and microstructure controlling during hot deformation. The hot deformation behavior of modified CNS-Ⅱ F/M steel was investigated through isothermal hot compression test at temperature ranging from 1223 to 1373 K and strain rate 001 to 10 s-1. The true stress-true strain data gained from compression tests were used to built constitutive equation of modified CNS-Ⅱ F/M steel. The influence of strain on the accuracy of constitutive analysis was incorporated, assuming strain has a influence on material constants. A 5th order polynominal equation with very good accuracy was used to represent the influence of strain on material constant. The flow stresses calculated from the constitutive equation were compared with test values in the whole experiment range and the absolute average error for the constitutive equation in predicting flow stress is 4728%. At last, the recrystallization behavior of modified CNS-Ⅱ F/M steel was investigated. The relationship of critical strain and peak strain with Zener-Hollomon parameter were given by an experimental equation.
关键词:
F/M steel
,
constitutive equation
,
dynamic recrystallization
YANG Ying
,
YAN Qing-zhi
,
MA Rong
,
GE Chang-chun
钢铁研究学报(英文版)
Ferritic/martensitic (F/M) steels have been recommended as one of the candidate materials for supercritical water cooled reactor (SCWR) in-core components use for its high thermal conductivity, low thermal expansion coefficient and inherently good dimensional stability under irradiation condition in comparison to austenitic steel. CNS-Ⅱ F/M steel which has good mechanical properties was one of the 9-12Cr F/M steels designed for SCWR in the previous work. In this study a modified CNS-Ⅱ F/M steel was used and it′s ultimate tensile strength was 925 MPa at room temperature and 483 MPa at 600 ℃ after optimizing heat treatment parameter. The ductile to brittle transition temperature of modified CNS-Ⅱ F/M steel is -55 ℃. Those are at the same level or even higher than that of CNS-Ⅱ and some commercial F/M steels nominated for SCWR in-core component use. The transmission electron microscope (TEM) results showed that the mechanical properties of the tempered martensite was closely related to the decomposition stage of the martensite.
关键词:
supercritical water reactor
,
ferritic/martensitic steel
,
cladding material
沈朝
,
段振刚
,
孙耀
,
张乐福
,
徐雪莲
腐蚀与防护
采用慢应变速率试验(SSRT)研究了12C>F/M钢在25 MPa,550℃和650℃的超临界水(SCW)中的机械性能,以及在550℃的SCW中的应力腐蚀开裂(SCC)倾向.同时通过均匀腐蚀试验研究了12Cr-F/M钢在550℃/25MPa的SCW中的腐蚀性能.SSRT结果表明,12Cr-F/M钢在550℃/25 MPa时具有优良的机械性能,当温度升高到650 ℃时其机械强度下降明显,但延伸率基本不变.由断口SEM形貌可知,12Cr-F/M钢具有沿晶应力腐蚀开裂(IGSCC)倾向.均匀腐蚀结果表明,12CpF/M钢在550℃/25MPa的SCW中的腐蚀性能较差,其腐蚀增重呈现出抛物线生长规律,1 000 h后其腐蚀增重达741mg/dm2.同时发现其在600 h时表面氧化膜出现裂纹,1 000 h时后观察到氧化膜发生剥落,而氧化膜脱落主要是因为在降温过程中基体与氧化物间不一致的热膨胀系数造成的.
关键词:
腐蚀
,
应力腐蚀开裂
,
机械性能
,
超临界水
胡武生
,
沈嘉年
,
李铁藩
,
彭晓
,
马信清
,
李美栓
,
周龙江
腐蚀学报（英文）
静态空气中氧化实验表明,低偏析镍基铸造高温合金M17F比普通镍基铸造高温合金M17F'(M17F的基础上+0.005%P、0.10%S和0.10%Zr)具有更低的恒温氧化增重速率,但氧化膜的粘附性更差。XRD、SEM和EDAX分析实验表明,两合金氧化膜的组成和结构基本相同。分析认为,M17F'合金中相对高含量的S、P和Zr的共同作用加速了该合金氧化膜的生长,另外该合金中0.1%含量的活性元素Zr改善了氧化膜的粘附性。
关键词:
低偏析镍基铸造高温合金
,
null
,
null
徐蕾
,
陈彩霞
,
吴申庆
复合材料学报
采用挤压铸造法制备了Al2O3短纤维增强M124F铝合金复合材料,并研究了其拉伸强度、基体凝固组织和界面.结果表明:用挤压铸造法制备的复合材料组织致密,纤维分布均匀,抗拉强度与M124F相比明显提高;基体组织的α-Al枝晶和Si相明显细化.分析表明,纤维的加入具有双重增强作用:高强度陶瓷纤维的介入增强了基体材料的力学性能;在凝固过程中,Al2O3短纤维阻碍了a-Al枝晶的生长,同时可作为Si相非自发形核的衬底,细化了基体组织,提高了复合材料的力学性能.纤维与基体间未发现界面生成物MgAl2O4.
关键词:
挤压铸造
,
氧化铝短纤维
,
M124F铝合金
,
拉伸强度
,
凝固组织
,
界面
那木吉拉图
,
阮永丰
,
苏小平
,
杨海
,
杨鹏
,
李楠
人工晶体学报
本文在CF4气氛中以提拉法成功地生长出高质量的掺入Tm3+、Ce3+的LiLuF4和LiYF4晶体,对比了Ar和CF4气氛中生长的LiYF4晶体的红外光谱特性,讨论了CF4气氛对LiM(M=Y,Lu)F4晶体生长的影响.同时测试了Tm3+、Ce3+在LiLuF4和LiYF4晶体中的有效分凝系数,从离子半径和晶胞畸变的角度,讨论了Tm3+、Ce3+在LiLuF4和LiYF4晶体中有效分凝系数差别的产生原因.
关键词:
LiYF4
,
LiLuF4
,
晶体生长
,
有效分凝系数
胡加学刘国权胡本芙肖翔
材料研究学报
运用Thermo--Calc软件进行热力学计算, 预测了一种新型9--12%Cr低活性F/M(铁素体/马氏体)实验钢的组织。对淬火回火热处理后的显微组织进行了观察, 并对析出物进行电子衍射结构分析和EDS化学成分检测。结果表明, 实验钢是典型的回火板条马氏体组织, 位于各种晶界上的析出物均为富Cr的碳化物M23C6, 其化学成分随碳化物的形貌变化而变化。对实验钢进行60%冷变形并随后在820℃退火10--300 min, M23C6在完全再结晶、奥氏体相变过程中进一步球化, Cr、W不断富集, Cr/Fe逐渐升高至2后成分趋于稳定, 化学组成接近于(Cr15Fe6W2)C6。
关键词:
金属材料
,
ferritic/martensitic steels
,
heat treatment
,
microstructure
,
carbides
胡加学
,
刘国权
,
胡本芙
,
肖翔
材料研究学报
运用Thermo-Calc软件进行热力学计算,预测了一种新型9-12%Cr低活性F/M(铁素体/马氏体)实验钢的组织.对淬火回火热处理后的显微组织进行了观察,并对析出物进行电子衍射结构分析和EDS化学成分检测.结果表明,实验钢是典型的回火板条马氏体组织,位于各种晶界上的析出物均为富Cr的碳化物M23C6,其化学成分随碳化物的形貌变化而变化.对实验钢进行60%冷变形并随后在820℃退火10-300min,M23C6在完全再结晶、奥氏体相变过程中进一步球化,Cr、W不断富集,Cr/Fe逐渐升高至2后成分趋于稳定,化学组成接近于(Cr15Fe6W2)C6.
关键词:
金属材料
,
铁素体/马氏体钢
,
热处理
,
显微组织
,
碳化物
