JIANG Zhouhua
,
DONG Yanwu
,
LIANG Lianke
,
LI Zhengbang
钢铁研究学报(英文版)
The pickup of hydrogen during electroslag remelting process for several slags consisting of CaF2Al2O3CaOSiO2MgO had been investigated. The laboratoryscale remelting experiments had been carried out in open air and waterfree argon atmosphere, and then the influencing factors were analyzed. It had been found that the hydrogen content in steel varied with different slag compositions. The compositions and state of slag had significant effect on the hydrogen level in steel. Partial return slag and premelted slag could avoid the hydrogen pickup especially in the early stages of the process. However, premelted slag was the optimum state to control the hydrogen pickup in steel. Experimental results indicated that waterfree argon atmosphere was very favorable to the control of hydrogen in steel in the normal remelting period.
关键词:
electroslag remelting; hydrogen; calcium fluoride; premelted slag; protective atmosphere
LI Huabing
,
JIANG Zhouhua
,
ZHANG Zurui
,
YANG Yan
钢铁研究学报(英文版)
The fine grained structures of nickelfree high nitrogen austenitic stainless steels had been obtained by means of cold rolling and subsequent annealing. The relationship between microstructure and mechanical properties and gain size of nickelfree high nitrogen austenitic stainless steels was examined. High strength and good ductility of the steel were found. In the grain size range, the HallPetch dependency for yield stress, tensile strength, and hardness was valid for grain size ranges for the nickelfree high nitrogen austenitic stainless steel. In the present study, the ductility of cold rolled nickelfree high nitrogen austenitic stainless steel decreased with annealing time when the grain size was refined. The fracture surfaces of the tensile specimens in the grain size range were covered with dimples as usually seen in a ductile fracture mode.
关键词:
grain refinement strengthening;nitrogen;nickelfree high nitrogen austenitic stainless steel;HallPetch equation
LI Huabing
,
JIANG Zhouhua
,
SHEN Minghui
,
YOU Xiangmi
钢铁研究学报(英文版)
A simple and feasible method for the production of high nitrogen austenitic stainless steels involves nitrogen gas alloying and adding nitrided ferroalloys under normal atmospheric conditions. Alloying by nitrogen gas bubbling in FeCrMnMo series alloys was carried out in MoSi2 resistance furnace and air induction furnace under normal atmospheric conditions. The results showed that nitrogen alloying could be accelerated by increasing nitrogen gas flow rate, prolonging residence time of bubbles, increasing gas/molten steel interfaces, and decreasing the sulphur and oxygen contents in molten steel. Nitrogen content of 069% in 18Cr18Mn was obtained using air induction furnace by bubbling of nitrogen gas from porous plug. In addition, the nickelfree, high nitrogen austenitic stainless steels with sound and compact macrostructure had been produced in the laboratory using vacuum induction furnace and electroslag remelting furnace under nitrogen atmosphere by the addition of nitrided alloy with the maximum nitrogen content of 081%. Pores were observed in the ingots obtained by melting and casting in vacuum induction furnace with the addition of nitrided ferroalloys and under nitrogen atmosphere. After electroslag remelting of the cast ingots, they were all sound and were free of pores. The yield of nitrogen increased with the decrease of melting rate in the ESR process. Due to electroslag remelting under nitrogen atmosphere and the consequential addition of aluminum as deoxidizer to the slag, the loss of manganese decreased obviously. There existed mainly irregular Al2O3 inclusions and MnS inclusions in ESR ingots, and the size of most of the inclusions was less than 5 μm. After homogenization of the hot rolled plate at 1 150 ℃×1 h followed by water quenching, the microstructure consisted of homogeneous austenite.
关键词:
nitrogen gas alloying;nitrided ferroalloy;high nitrogen austenitic stainless steel;vacuum induction melting;electroslag remelting
DONG Yanwu
,
JIANG Zhouhua
,
LI Zhengbang
钢铁研究学报(英文版)
Experiment was carried out after the process parameters were calculated by the model previously established. The relationship between interdendritic spacing and local solidification time (LST) mainly determined by process parameters was exposed. Furthermore, the extent of segregation was studied. The results indicate that LST and interdendritic spacing are the largest and the amount of Laves phase as a result of the niobium segregation is the highest in the center of the ingot, whereas the opposite results are obtained at the edge of ingot. The extent of element segregation and the amount of Laves phase can be reduced when appropriate parameters are used. Therefore, the duration of subsequent homogenization treatments for 718 is shortened and the alloy quality is improved.
关键词:
electroslag remelting;Inconel 718;segregation;local solidification time;interdendritic spacing
ZHAN Dongping
,
ZHANG Huishu
,
JIANG Zhouhua
钢铁研究学报(英文版)
To confirm the effects of AlMnCa and AlMnFe alloys on the deoxidization and modification of Al2O3 inclusions, experiments of 4heat low carbon and low siliconaluminum killed steels deoxidized by AlMnCa and AlMnFe alloys were done in a MoSi2 furnace at 1 873 K. It is found that the 1# AlMnCa alloy has the best ability of deoxidization and modification of Al2O3 inclusions than 2# AlMnCa and AlMnFe alloys. Steel A deoxidized by 1# AlMnCa alloy has the lowest total oxygen content in the terminal steel, which is 37×10-6. Most of the inclusions in the steel deoxidized by 1# AlMnCa alloy are spherical CaOcontaining compound inclusions, and 891% of them are smaller than 10 μm. The diameter of the inclusion bigger than 50 μm is not found in the final steels deoxidized by AlMnCa alloys. Whereas, for the steels deoxidized by AlMnFe alloys, most inclusions in the terminal steel are Al2O3 or Al2O3MnO inclusions, and a few of them are spherical, and only 768% of them are smaller than 10 μm. Some inclusions bigger than 50 μm are found in the steel D deoxidized by AlMnFe alloy.
关键词:
steelmaking;deoxidization;inclusion;AlMnCa alloy;AlMnFe alloy
Journal of Materials Research
The morphology of the dark and bright regions observed by transmission electron microscopy for the Zr(64.13)Cu(15.75)Ni(10.12)Al(10) bulk metallic glass strongly depends on the ion beam parameters used for ion milling. This indicates that the ion beam could introduce surface fluctuation to metallic glasses during ion milling.
关键词:
room-temperature
Physical Review B
In order to understand the unusually large value of zero-field splitting D for the axial Fe3+ center in a KTaO3 crystal, Zhou made two assumptions in his recent report [Phys. Rev. B 42, 917 (1990)]. In this Comment we will show that his assumption II is qualitatively reasonable, whereas assumption I is unnecessary and doubtful.
关键词:
electric-field;srcl2
Journal of Physics and Chemistry of Solids
The layered ternary ceramics Ti3SiC2 and Ti3AlC2 are isostructural and can form Ti3Si1-xAlxC2 solid solutions combining the advanced properties of both compounds [H.B. Zhang, Y.C. Zhou, Y.W. Bao, M.S. Li, Improving the oxidation resistance of Ti3SiC2 by forming a Ti3Si0.90Al0.1C2 solid solution, Acta Mater. 52 (2004) 3631-3637; E.D. Wu, J.Y. Wang, H.B. Zhang, Y.C. Zhou, K. Sun, Y.J. Xue, Neutron diffraction studies of Ti3Si0.9Al0.1C2 compound, Mater. Lett. 59 (2005) 2715-2719; J.Y. Wang, Y.C. Zhou, First-principles study of equilibrium properties and electronic structure of Ti3Si0.75Al0.25C2 solid solution, J. Phys.: Condens. Matter 15 (2003) 5959-5968; Y.C. Zhou, J.X. Chen, J.Y. Wang, Strengthening of Ti3AlC2 by incorporation of Si to form Ti3Al1-xSixC2 solid solutions, Acta. Mater. 54 (2006) 1317-1322]. In the present work, the solid solutions of Ti3Si1-xAlxC2 (x = 0, 0.25, 0.33, 0.5, 0.67, 0.75, 1) are investigated by first-principle calculations based on pseudo-potential plan-wave method within the density functional theory framework. The results show that as Al content increases in the solid solution, all the bonds have weakened to certain extents, which lead to an unstable structure both energetically and geometrically. The calculated results are compared and discussed with the reported data for the Ti3Si1-xAlxC2 solid solutions. (c) 2007 Elsevier Ltd. All rights reserved.
关键词:
ceramics;ab initio calculations;electronic structure;electrical;conductivity;oxidation behavior;mechanical-properties;ti3sic2;temperature;ti3alc2;air;si
李玉伟
,
陈继红
,
唐东明
,
张豹山
,
鹿牧
,
陆怀先
功能材料与器件学报
doi:10.3969/j.issn.1007-4252.2010.02.011
制备了一系列具有铁磁/反铁磁交换偏置作用的[NiO/Fe65Co35]10多层膜,使用振动样品磁强计(VSM)测量了样品的静磁参数,利用微带线法测量了样品4GHz-10GHz的磁谱,首次制备并测得了自然共振频率(fr)在6GHz以上,最高到f=9.6GHz的薄膜样品.结果表明交换偏置场(Hex)、各向异性场(Hua)、以及矫顽力(Hc)随铁磁层厚度(tFM)增大而减小;基于Landau-Lifishitz (L-L)方程对静磁参量和磁谱进行了比较,发现样品自然共振频率较L-L方程计算值偏大30%以上.
关键词:
铁磁
,
反铁磁
,
交换偏置场
,
各向异性场
,
交换耦合能密度
,
自然共振频率
倪永中
,
徐鸿
材料科学与工程学报
本文提出了一种基于粒子群算法和有限元方法的弹塑性本构方程参数的确定方法,并在此基础上开发了参数自动优化系统CMPI(Constitutive Material Parameter Identification).通过使最小二乘形式的目标函数达到极小值,实现参数的动态寻优;模型参数作为粒子群优化模块的输入,采用应变(应力)控制方法,调用材料非线性有限元模块计算特定参数时的应力(应变)响应,并计算与实验数据的误差,从而实现优化过程.CMPI目前适用于A-F类模型(Chaboehe、Ohno-Wang、Jiang-Sehitoglu)的参数优化,以此为基础,不难扩展到其他材料模型.
关键词:
粒子群
,
材料非线性
,
有限元
,
Ohno-Wang 模型
