Fengli SUI
,
Liqing CHEN
,
Xianghua LIU
,
Lintao WANG
,
Wei LI
金属学报(英文版)
doi:10.1016/S1006-7191(08)60074-5
A coupled thermo-mechanical model containing metal flow and temperature field for calculating temperature variation has been developed on fourteen-pass hot continuous rolling of round rod for Inconel 718 alloy using 3D elastic-plastic finite element method (FEM). The temperature of characteristic analysis points in the intermediate cross-section of the workpiece has been simulated at initial temperature ranging from 960 to 1000 ℃ and initial velocity in range of 0.15-0.55 m．s-1. Based on finite element analysis and microstructural observation in cylindrical hot compression experiments, the appropriate hot continuous rolling technologies have been designed for rod products with different diameters. For a real rolling practice, the simulated surface temperature was examined and is in good agreement with the measured one.
关键词:
Hot continuous rolling
,
null
,
null
,
null
,
null
Liqing CHEN
材料科学技术（英文）
The 42.1 vol. pct TiC/AZ91D magnesium-matrix composites with interpenetrating networks were fabricated by in-situ reactive infiltration process. The compressive creep behavior of as-synthesized composites was investigated at temperature ranging from 673 to 723 K under loads of 95-108 MPa. For a comparative purpose, the creep behavior of the monolithic matrix alloy AZ91D was also conducted under loads of 15-55 MPa at 548-598 K. The creep mechanisms were theoretically analyzed based on the power-law relation. The results showed that the creep rates of both TiC/AZ91D composites and AZ91D alloy increase with increasing the temperature and load. The TiC/AZ91D composites possess superior creep resistance as compared with the AZ91D alloy. At deformation temperature below 573 K, the stress exponent n of AZ91D alloy approaches theoretical value of 5, which suggests that the creep process is controlled by dislocation climb. At 598 K, the stress exponent of AZ91D is close to 3, in which viscous non-basal slip deformation plays a key role in the process of creep deformation. However, the case differs from that of AZ91D alloy when the stress exponent n of TiC/AZ91D composites exceeds 9, which shows that there exists threshold stress in the creep process of the composites, similar to other types of composites. The average activation energies for the creep of the AZ91D alloy and TiC/AZ91D composites were calculated to be 144 and 152 kJ/mol, respectively. The existence of threshold stress in the creep process of the composites leads to an increase in activation energy for creep.
关键词:
Magnesium-matrix composites
,
composites
,
TiC/AZ91D
,
in
Liqing CHEN
,
Naoyuki Kanetake
材料科学技术（英文）
Ingot metallurgy (IM) aluminum has long been the subject and attracted the attention of many metallurgists and textural researchers of materials. Due to the introduction of large amounts of ex situ interfaces, however, the textures in powder metallurgy (PM) processed aluminum has been rarely reported. In this article, a pure aluminum plate was prepared $via$ PM route. The starting billet was first produced with uni-axially cold compaction and flat hot-extrusion and then followed by cold rolling processes. The hot-extruded and cold rolling deformation textures of the pure PM aluminum at 50%, 80% and 90% cold rolling reductions were studied by orientation distribution functions (ODFs) analysis. The finite element polycrystal model (FEPM) was finally utilized to simulate the cold rolling textural evolution at various stages of cold rolling. In FEPM simulation, the initial hot-extruded textures were taken into account as inputs. The results showed that typical β-fiber texture formed in pure PM aluminum with the cold rolling reduction increased till 80%, and there was not much change after excessive cold rolling deformation. Homogeneous slip is not the only deformation mode in PM processed pure aluminum plate at over 80% cold rolling reduction. The experimental results were qualitatively in good agreement with the simulated ones.
关键词:
Texture
,
null
,
null
,
null
,
null
李开明
,
李亚洲
,
冯维贵
,
林长
量子电子学报
doi:10.3969/j.issn.1007-5461.2007.05.014
采用非线性反馈控制,用附加了带参数的正弦项对Chen系统进行了有效的控制.随着参数k的逐渐增大,系统的动力学行为呈现出一系列的变化.数值研究结果表明:随控制参数的增大,驱动信号的强度渐大,混沌系统由混沌运动到周期轨道,最终到一相点.
关键词:
混沌
,
Chen系统
,
不动点
,
Lyapunov指数
,
反馈控制
Journal of Materials Research
The morphology of the dark and bright regions observed by transmission electron microscopy for the Zr(64.13)Cu(15.75)Ni(10.12)Al(10) bulk metallic glass strongly depends on the ion beam parameters used for ion milling. This indicates that the ion beam could introduce surface fluctuation to metallic glasses during ion milling.
关键词:
room-temperature
金属学报
Volu扣ne 27SeriesB1991AUTHOR INDEX CCAO Guanghan(曹光旱)············……6一B科6CAo weijie(曹卫恋)..················……5一B32oCAO Yilin(曹益林)··················……6一B443CHANG Xin(常听)···············……1一B48CHE Guang邻n(车广灿)·············一6一B科0CHEN Erbao(陈二保)···············……6一B410CHEN Jia....
关键词:
高诚
,
胥蕊娜
,
陈黎
,
姜培学
工程热物理学报
格子Boltzmann方法(LBM)在计算复杂结构物理模型时具有独特优势并在模拟两相流动过程中能够高效清晰捕捉相界面.本文介绍了基于Shan-Chen多相模型的格子Boltzmann方法的理论成果以及基于二氧化碳封存的超临界两相流的模拟研究.结果表明,Shan-Chen模型在模拟两相流时符合Laplace定律,且两相层流时的速度分布和相渗曲线均与理论值吻合.二氧化碳封存过程中,较大的注入速率在提高二氧化碳残余俘获量的同时会降低其化学俘获量.
关键词:
二氧化碳封存
,
超临界两相流
,
Shan-Chen模型
中国腐蚀与防护学报
N。1Atmospheric Corrosivlty for Steels………………………………………………… .LIANG Caideng HO[I i。-tat（6）Caustic Stress Corrosion Cr。king of Alloy 800 Part 2.The Effect of Thiosul执e……………………………………… KONG De-sheng YANG Wu ZHAO Guo-zheng HUANG De.ltL。ZHANG Yu。。he CHEN She。g-bac（13）SERS slid E16CttOCh6iniC81 Stlldy Of Illhibit1Oli M6ch＆tllsth Of ThlollY68 Oil ITOll ID H....
关键词:
