WAN Fei
,
WANG Yong-qin
,
QIN Shu-ren
钢铁研究学报(英文版)
The mechanism for heat transfer of radiation is usually adopted to heat strip in vertical continuous annealing furnace. The rate of heat transfer among strip and other objects can be hugely affected by the parameters of strip speed, geometry factors and radiating characteristic of surfaces of strip, radiating tubes and walls of furnace. A model including all parameters is proposed for calculating the heat transfer coefficient, predicting the strip temperature and boundary temperature of strip through analyzing these parameters. The boundary temperature is a important datum and different from average arithmetic value of temperature of strip and temperature in furnace. Also, the model can be used to analyze the relation for temperature of strip and heat transfer coefficient, total heat transfer quantity and heating time. The model is built by using the radiating heat transfer rate, the Newton′s law of cooling, and lumped system analysis. The results of calculation are compared to the data from production line. The comparisons indicate that the model can well predict the heating process. The model is already applied for process control in production line. Also, this research will provide a new method for analyzing the radiation heat transfer.
关键词:
vertical continuous annealing furnace (VCAF)
,
radiation tube section (RTS)
,
radiation heat transfer
,
heat transfer coefficient
,
heat transfer rate
张麦仓
,
董建新
,
曾燕屏
,
谢锡善
,
罗子健
金属学报
利用热力耦合有限元程序FORMT,对PM René 95合金中等尺寸(外径尺寸约为630 mm)涡轮盘的等温锻造工艺进行了模拟式设计.结果表明,采用TZM钼基合金模具,在1050℃以接近10-3s.的应变速率进行闭式模锻和开式模锻,模具材料均能满足使用要求,且开式模锻设备最大载荷不超过31×103kN;采用K21合金模具,在1000℃以相同条件等温成形,模具材料因变形热效应及边界摩擦引起温升而失效且所需设备吨位相对较大.
关键词:
PM
,
null
,
null
,
null
张麦仓
,
董建新
,
曾燕屏
,
谢锡善
,
罗子健
金属学报
doi:10.3321/j.issn:0412-1961.2002.10.022
利用热力耦合有限元程序FORMT,对PM René 95合金中等尺寸(外径尺寸约为630 mm)涡轮盘的等温锻造工艺进行了模拟式设计.结果表明,采用TZM钼基合金模具,在1050℃以接近10-3s.的应变速率进行闭式模锻和开式模锻,模具材料均能满足使用要求,且开式模锻设备最大载荷不超过31×103kN;采用K21合金模具,在1000℃以相同条件等温成形,模具材料因变形热效应及边界摩擦引起温升而失效且所需设备吨位相对较大.
关键词:
PM René 95合金,等温锻造,热力耦合有限元,模拟式工艺设计
付锐
,
陈希春
,
任昊
,
冯涤
航空材料学报
doi:10.3969/j.issn.1005-5053.2011.3.002
自行设计开发了适合工业化生产高纯净,低偏析,无宏观缺陷铸锭的电渣重熔连续定向凝固技术(ESR-CDS)的设备和工艺,利用该技术成功制备了直径为φ150mm的René88DT合金定向凝周铸锭.采用XRD测试了定向凝固柱状晶的生长取向,结果表明,ESR-CDS René88DT铸锭柱状晶择优生长方向为<100>系晶向;ERS-CDS铸锭与传统ESR铸锭相比,枝晶组织生长方向保持一致,二次枝晶臂均匀细小,元素偏析程度低,且晶间一次析出相呈颗粒状,尺寸细小;等温热压缩实验结果表明,ESR-CDS René88DT合金热压缩试样在1100℃,0.0-50.1s-1应变速率下可达到70%以上压缩变形量并获得均匀细小的动态再结晶组织;ESR-CDS René88DT合金铸锭经等温锻造制备出了φ170mm×73mm的饼坯件,锻压变形量超过70%,饼坯件除上下两端的变形死区外均发生了动态再结晶,晶粒尺寸约50μm.
关键词:
电渣重熔连续定向凝固
,
热变形
,
动态再结晶
李晓
,
董建新
,
张丽娜
,
张麦仓
,
胡尧和
,
谢锡善
,
国为民
金属学报
经不同固溶时效处理的PM René 95合金于650℃分别在蠕变、保载5和90 s疲劳载荷条件下进行了裂纹扩展速率实验.结果表明,相同热处理制度下,疲劳保载时间越长,裂纹扩展速率越高;相同载荷条件下,增加一次高温固溶并缓冷,有利于降低合金的裂纹扩展速率,且固溶温度越高裂纹扩展速率越低;1200℃一次固溶缓冷并于1160℃二次固溶热处理比1140℃一次固溶的裂纹扩展速率约降低一个数量级;基体晶粒尺寸适当加大,强化相粒子γ′c数量增加、形状趋于田字形,有利于降低裂纹扩展速率.
关键词:
René
,
null
,
null
李晓
,
董建新
,
张丽娜
,
张麦仓
,
胡尧和
,
谢锡善
,
国为民
金属学报
doi:10.3321/j.issn:0412-1961.2001.10.012
经不同固溶时效处理的PM René 95合金于650℃分别在蠕变、保载5和90 s疲劳载荷条件下进行了裂纹扩展速率实验.结果表明,相同热处理制度下,疲劳保载时间越长,裂纹扩展速率越高;相同载荷条件下,增加一次高温固溶并缓冷,有利于降低合金的裂纹扩展速率,且固溶温度越高裂纹扩展速率越低;1200℃一次固溶缓冷并于1160℃二次固溶热处理比1140℃一次固溶的裂纹扩展速率约降低一个数量级;基体晶粒尺寸适当加大,强化相粒子γ′c数量增加、形状趋于田字形,有利于降低裂纹扩展速率.
关键词:
René 95粉末高温合金,裂纹扩展速率,热处理
刘守平
,
周上祺
,
王佳眉
,
任勤
腐蚀学报（英文）
用金相显微镜、扫描电镜、X射线衍射仪和X射线能谱仪对天然气井油管悬挂器腐蚀失效进行了检测分析，并对天然气井油管悬挂器用35CrMo钢进行了盐雾试验，结果表明，天然气中的水和CO2是引起腐蚀的主要介质，腐蚀产物主要是FeCO3，高速天然气冲刷和钢中的非金属夹杂加剧了腐蚀的速度.
CORROSION FAILURE ANALYSIS OF AN OIL TUBE USED IN NATURAL GAS WELL
LIU Shou-ping,ZHOU Shang-qi,WANG Jia-mei,REN Qin
Chongqing University
A failed oil tube used in natural gas well was examined by optical microscope,scanning electron microscope ,X-ray diffractometer and X-ray spectrometer.Corrosion behavior of 35CrMo steel samples of the oil tube were investigated by means of salt spray tests in the laboratory.The results show that CO2 and H2O are primary factors in the corrosion of oil tube.The corrosion product is FeCO3,non-metallic inclusions in the steel and erosion of natural gas fluid played an important role in accelerating the corrosion.
oil tube;
natural gas well；
35CrMo steel；
failure analysis；
corrosion
关键词:
悬挂器
,
null
,
null
,
null
张鸿冰
,
倪乐民
,
徐祖耀
金属学报
经 LFG(ΔG~(γ→a))-Mogutnov(ΔG_(Fe)~(γ→a))、徐祖耀(Shu-A)(ΔG~(γ→a))-Orr-Chipman(ΔG_(Fe)~(γ→a))、徐祖耀(Shu-B)(ΔG~(γ→a))-Orr-Chipman(ΔG_(Fe)~(γ→a))组合,均可算得 Fe-Mn-C 合金的 Ms 温度且与实验值十分符合.所得结果经数学处理,得 Fe-Mn-C 系 Ms 与成分的关系为:Ms(K)=817.4-7513.4xc-4141.9x_(Mn)-32083.5x_Cx_(Mn)(LFG)Ms(K)=829.9-7580.5x_C-4166.0x_(Mn)-15727.8x_Cx_(Mn)(SHU-A)Ms(K)=829.2-7276.1x_C-2915.4x_(Mn)-43825.7x_Cx_(Mn)(SHU-B)其线性相关系数均大于0.992.C 和 Mn 浓度均使合金的 Ms 线性地降低,而碳的作用几乎是Mn 的两倍.处理中引入了合金元素交互作用项(x_Cx_(Mn)),表明 C,Mn 相互加剧对 Ms 的影响。随含 C,Mn 量的增加,相变驱动力均单调地增加,而不存在奇异点.Ms 和相变驱动力的计算值均依赖于ΔG_(Fe)~(γ→a)项.
关键词:
Journal of Materials Processing Technology
The crystallization temperatures and other thermal properties have been measured systematically for two ternary Cu-Ni-P and two quaternary Cu-Ni-Sn-P amorphous systems. The dependence of crystallization temperature on the composition for the four alloy systems can not be described basically by the usual used Naka rule. The Gibbs free energy of crystallization can be calculated for the alloy systems with the model proposed by Shu et al. Using the calculated free energy of crystallization, it is still not possible to properly describe all of the crystallization temperatures of the alloy systems. However, it has been found that the correlation between the crystallization temperature and the content of the alloy systems can be reasonably explained by the nucleation and growth rates of a new phase for the classical theory of phase transformation. It has been established that the classical theory of phase transformation can be used to describe the thermal stability of the Cu-based amorphous alloys during their crystallization process. (C) 1999 Published by Elsevier Science S.A. All rights reserved.
关键词:
thermal stability;amorphous alloys;Cu-P based alloy systems;classical;theory of phase transformation;solid-liquid interface;structural model;glasses
