SHEN Guangjun WANG shidong ZHANG Jinping Lab.of Solid State Microstructure
,
Nanjing University
,
Analysis and Testing Centre
,
Southeast University
,
Nanjing
,
China Associate Professor
,
Analysis and Testing Centre
,
Southeast University
,
Nanjing
,
210018
,
China
金属学报(英文版)
A secondary twinning orientation relationship between A and B martensite variants in a CuZnAl shape memory alloy was confirmed under TEM observation.The twin plane, (50),is a linear combination of (8)and(1 0 10)planes,which are twin planes of A:C and A:D type pair respectively.
关键词:
shape memory alloy
,
null
,
null
,
null
Acta Physica Polonica A
A novel technique, with which in situ TiB2 particles and serpentine channels are introduced to prepare wrought aluminum alloy with higher strength, has been successfully applied to produce semi-solid 7075 alloy slurry. The effects of in situ TiB2 particles and serpentine channels on the microstructure of the 7075 alloy including the grain growth behavior in the semi-solid state of the 7075 alloy were investigated. The experimental results showed that the in situ TiB2 particles and serpentine channels are beneficial to increase the number of solidification nuclei and to promote uniform distribution of alpha-Al nuclei. As a result, the semi-solid 7075 alloy slurry with globular-like grains has been successfully produced.
关键词:
Materials Science and Engineering a-Structural Materials Properties Microstructure and Processing
The microstructural evolution during solidification and subsequent solid-state transformation of AISI 304 stainless steel is studied by directional solidification and quenching methods in this paper. The phase transformation sequence in the steel directionally solidified is that the precipitation of primary ferritic dendrites, ferrite-austenite eutectic reaction, and the direct formation of austenite occur in sequence during the directional solidification of the austenitic stainless steel. At the eutectic reaction stage, plenty of columnar and cellular eutectic colonies composed of the coupled growth of lamellar ferrite and austenite take place. During the course of subsequent solid-state transformation, austenite grows into ferrite gradually, resulting in the disappearing of eutectic colonies and thinning of primary ferritic dendrites, and dendrite cores of primary ferrite are retained as the final skeletal ferrite in the final microstructure. (c) 2006 Elsevier B.V. All rights reserved.
关键词:
austenitic stainless steel;directional solidification;eutectic colony;austenitic stainless-steel;cr-ni alloys;sequence;welds
Physical Review B
Metastable Fe100-xAlx alloys have been formed by ball milling of elemental Fe and Al powders: supersaturated body-centered-cubic solid solutions for x less than or equal to 70, and an amorphous phase for x > 70. Quantitative x-ray-diffraction measurements show that the total root-mean-square displacement (rms) and the static rms in the Fe100-xAlx solid solutions increase significantly with increasing Al content, The total rms at the instability point, however, reaches only 6.8% of the nearest-neighbor distance and is far below the critical value predicted by the Lindemann melting criterion, suggesting that the Lindemann melting criterion is not applicable for the solid-state amorphization. Instead. the Debye temperature of the supersaturated Fe100-xAlx alloys was observed to drop by similar to 22% at the point of amorphization, implying a corresponding softening in the average shear modulus of similar to 40%, which agrees with the microhardness measurements. These results strongly support the empirical elastic instability criterion For the solid-state amorphization process.
关键词:
to-glass transition;crystal;transformation
Journal of Alloys and Compounds
Growth kinetics and interfacial morphologies of the intermetallic compounds (IMCs) between single crystal Ag and Sn-4Ag, Sn-3Cu and Sn-37Pb solders were investigated by solid-state aging at 160 degrees C and liquid-state aging at 260 degrees C. Isothermal equation of chemical reaction and phase diagrams were used to explain the effects of Ag, Cu and Pb on the growth kinetics of IMCs under solid-state and liquid-state aging conditions. The diffusion coefficients for the three solder joints of Sn-4Ag/Ag, Sn-3Cu/Ag and Sn-37Pb/Ag were calculated after solid-state and liquid-state aging. It is found that Pb can effectively retard the growth of IMCs during liquid-state aging but has little influence on the growth rate of IMCs during the solid-state aging. Some local small cracks were frequently observed in the Cu(6)Sn(5) particles near interfaces of the Sn-3Cu/Ag solder joints after solid-state aging for several days. However, there were no such local small cracks when solders or interfaces did not contain the Cu(6)Sn(5) particles after the same aging time. (C) 2008 Elsevier B.V. All rights reserved.
关键词:
Ag single crystal substrate;Lead-free solder;Intermetallic compounds;(IMCs);Growth kinetics;Local cracks;lead-free solders;electroless ni(p) metallization;intermetallic;compound;cu-sn;joints;ni;bi;nanoindentation;microstructure;wt.percent
Journal of Applied Physics
Interdiffusion-induced solid-state amorphization reaction (SSAR) in polycrystalline Ni/amorphous Si multilayers has been studied using an in situ x-ray diffraction technique together with transmission electron microscope observations, The amorphization reaction was found to occur both on the Ni/Si interfaces in terms of a planar-layer growth model and along the grain boundaries in the Ni sublayers. Thermodynamic and kinetic interpretations for the SSAR at grain boundaries are presented and an amorphous growth model is also suggested for elucidating the SSAR in polycrystalline Ni/amorphous Si multilayers.
关键词:
x-ray-diffraction;thin-films;silicon
R.B. Song
,
Y.L. Kang
,
J.L. Sun
金属学报(英文版)
The experimental study on the familiar 60Si2Mn and 1Cr18NigTi materials rolled in the semi-solid state was carried out. Experimental results show that the segregation of liquid occurs when the semi-solid slurry is rolled, which influences the microstructure and mechanics performance of workpiece under room temperature. The globular solid particles don't present plastic deformation unless high solid fraction. At the same time, the mechanics property of workpiece is pretty good while the semi-solid slurry of 1Cr18NigTi material is rolled by a pass and no other treatment.
关键词:
semi-solid slurry
,
null
,
null
,
null
,
null
Materials Science and Engineering a-Structural Materials Properties Microstructure and Processing
We report on studies of solid state redox reactions induced by mechanical alloying (MA). The displacement reaction in the Fe-CuO system during MA may be completed by two steps: a rapid self-sustaining combustion reaction process, followed by a gradual reaction process. High densities of point and lattice defects, as well as a fine dispersion of reactants, are introduced in the powder mixture during MA. In addition, the displacement reaction in the Fe-CuO system produces a large negative heat. This combination of factors makes the redox reaction occur in the reaction regions, accompanied by self-heating. The self-heating may raise the temperature up to ignition temperature for a combustion reaction; this ignition temperature is greatly decreased by ball-milling. Combustion then takes place. The displacement reaction may be carried out rapidly during combustion. Complete reduction of copper oxides, including the intermediate oxidation state phase, Cu2O, appearing immediately after combustion, is observed after prolonged milling, during which the reduction is gradual; a similar self-sustaining reaction mechanism works in local reaction regions.
关键词:
amorphous-alloys;powders
