TANG Ping
,
XU Chushao
,
WEN Guanghua
,
ZHAO Yanhong
,
QI Xin
钢铁研究学报(英文版)
An experimental apparatus for simulating copper mold is used to quantify the heat flux through the slag film and to obtain a solid slag for further determining its crystallization behavior. The result indicates that both the chemical composition of the mold powder and the cooling rate have an important influence on the heat flux through the slag film. With increasing the binary basicity, the heat flux of slag film decreases at first, reaches the minimum at the basicity of 14, and then increases, indicating that the maximum binary basicity is about 14 for selecting “mild cooling” mold powder. The heat transfer through the slag film can be specified in terms of the crystalline ratio and the thickness of the slag film. Recrystallization of the solid slag occurs and must be considered as an important factor that may influence the heat transfer through the solid slag layer.
关键词:
continuous casting;mold powder;slag film;heat flux;crystallization
YU Xiong
,
WEN Guanghua
,
TANG Ping
,
MA Fanjun
,
WANG Huan
钢铁研究学报(英文版)
Because of the addition of significant quantities of Al and Mn, the great challenge of casting 20Mn23Al non-magnetic steel is to design a mold slag that is chemically compatible with this steel chemistry. In this paper, a new mold slag with low melting point, low basicity was proposed. The initial slag (the base mold slag) and two corresponding spent mold slag (8min slag and 15min slag), which was sampled from the caster after 8 minutes and 15minutes of casting, were investigated, the changes of mold slag composition and properties of molten slag were discussed. The results showed that:(i) The slag quickly changed in chemistry to a slag that contained a low quantity of silica and a higher quantity of alumina, and the basicity increased obviously; (ii) Heat flux density through the slag film decreased appreciably with the time increase; (iii) Mold slag used for non-magnetic steel precipitated CaF2 crystals; (iv) The slab has good surface quality with not occurrences of longitudinal face cracks and slag inclusions; (v) The Al2O3 content in the molten slag pool increased with time, and Al2O3 concentration of the pool can be regarded as being in a practically equilibrium state after about 600sec.
关键词:
Non-magnetic steel;Continuous casting;Mold slag;Viscosity;CaF2
XU Hailun
,
WEN Guanghua
,
SUN Wei
,
et al
钢铁研究学报(英文版)
Finite element models of steady heat conduction in the meniscus region of beam blank mold were developed by using ABAQUS software. The effect of mold grinding thickness, cooling water velocity, diameter of restrictor rods and water channel design on hot face temperature was analyzed in detail. Attention was focus on the peak temperature and temperature uniformity along hot face. The results showed that the peak temperature of existing mold, about 337.2 oC, is located in the fillet, and two valleys of hot face temperature are found in flange corner and junction of wide face and narrow face, respectively. Decreasing mold thickness, increasing cooling water velocity and increasing diameter of restrictor rods can all reduce peak temperature and improve temperature uniformity along hot race at the expense of lower overall temperature. Redesigning the water channel can decrease peak temperature and thermal gradient of mold without lowering overall temperature of hot face. In particular, the small hole design can improve temperature uniformity across hot face to the best advantage.
关键词:
beam blank;continuous casting mold;thermal behavior;temperature distribution
WEN Guanghua
,
LIU Hui
,
TANG Ping
钢铁研究学报(英文版)
The isothermal and nonisothermal experiments were performed to construct the continuous cooling transformation (CCT) and temperature time transformation (TTT) diagrams of four industrial mold fluxes through visual observations in an experimental apparatus based on the single hot thermocouple technique (SHTT). The results of the CCT diagrams indicate that ① the crystallization temperature of mold fluxes lowers as the cooling rate increases, ② the mold fluxes have larger critical cooling rate, higher crystallization temperature, and less onset time of crystallization when the basicity increases or the viscosity decreases, ③ the influences of the melting points of the mold fluxes on their crystallization tendency are not significant. Isothermal tests show that the onset time of crystallization decreases at first, and then increases, and finally represents a “C” shape with increasing isothermal temperature. The TTT diagrams of four industrial mold fluxes were divided into two separate “C” shape regions. The crystal phase of C20A selected was analyzed by Xray diffraction, which is cuspidine (Ca4Si2O7F2) over 1 100 ℃ and calcium silicon oxide fluoride (Ca2SiO2F2) below 1 100 ℃. When compared with the TTT diagram, the CCT diagram can provide a more realistic estimate of the critical cooling rate of the mold fluxes. Thus, both the CCT and TTT diagrams can unambiguously describe the crystallization phenomena of the mold fluxes.
关键词:
mold flux;CCT;TTT;critical cooling rate;crystallization
金属学报
Volu扣ne 27SeriesB1991AUTHOR INDEX CCAO Guanghan(曹光旱)············……6一B科6CAo weijie(曹卫恋)..················……5一B32oCAO Yilin(曹益林)··················……6一B443CHANG Xin(常听)···············……1一B48CHE Guang邻n(车广灿)·············一6一B科0CHEN Erbao(陈二保)···············……6一B410CHEN Jia....
关键词:
李玉伟
,
陈继红
,
唐东明
,
张豹山
,
鹿牧
,
陆怀先
功能材料与器件学报
doi:10.3969/j.issn.1007-4252.2010.02.011
制备了一系列具有铁磁/反铁磁交换偏置作用的[NiO/Fe65Co35]10多层膜,使用振动样品磁强计(VSM)测量了样品的静磁参数,利用微带线法测量了样品4GHz-10GHz的磁谱,首次制备并测得了自然共振频率(fr)在6GHz以上,最高到f=9.6GHz的薄膜样品.结果表明交换偏置场(Hex)、各向异性场(Hua)、以及矫顽力(Hc)随铁磁层厚度(tFM)增大而减小;基于Landau-Lifishitz (L-L)方程对静磁参量和磁谱进行了比较,发现样品自然共振频率较L-L方程计算值偏大30%以上.
关键词:
铁磁
,
反铁磁
,
交换偏置场
,
各向异性场
,
交换耦合能密度
,
自然共振频率
周晓宏
,
刘红军
,
刘鹏
功能材料
优化技术是一种以数学为基础,可用来求解各种工程问题最优解的应用技术.本文利用磁流变阻尼器动态特性数据,采用遗传算法进行阻尼器模型参数识别优化过程,最终将得到的磁流变阻尼器模型参数用于土木工程结构振动控制研究.已建立的磁流变阻尼器的动力特性将在不同的电场强度和变化的位移幅度下进行测试,可以得到在不同位移和速度下恢复力的滞回曲线,建立Bouc-Wen模型.把根据试验得到的滞回曲线和使用遗传算法对模型参数进行优化的结果进行比较可知,这种模型的参数可以以十分小的误差得到优化.
关键词:
遗传算法
,
阻尼器
,
参数识别
吕友军
,
董旭斌
,
张天宁
工程热物理学报
本文采用基于颗粒动力学的欧拉双流体模型,对比研究了曳力和湍流对超临界水流化床传热特性的影响,选取了Gidaspow、Syamlal-O'Brien和Wen-Yu三种曳力模型以及标准κ-ε、RNG κ-ε、Realizable κ-ε湍流模型三种高Re数湍流模型及低Re数κ-ε湍流模型.研究结果表明,在三种曳力模型中,Gidaspow曳力模型在超临界水流化床中更为适用;对于所采用的四种κ-ε湍流模型,利用三种高雷诺数湍流模型模拟所得床层与壁面间传热系数基本一致且大于采用低雷诺数模型模拟所得传热系数,而综合考虑,RNGκ-s湍流模型更适于超临水流化床传热特性的研究.
关键词:
超临界水流化床
,
曳力
,
湍流
,
传热
朱奎松
,
刘松利
,
芶淑云
,
王梁
钢铁钒钛
doi:10.7513/j.issn.1004-7638.2017.02.005
基于欧拉-双流体模型和流态化氯化临界流化速度经验公式,结合云南高钛渣物性参数,研究了其流态化氯化的初始流化速度下高钛渣流态化氯化特性、气泡运动对床层的扰动、气泡大小与分布板位置关系.研究结果表明:Grace方程能准确预测B类颗粒窄粒径的高钛渣流态化氯化气泡行为,Wen-Yu方程预测的初始流化速度下乳相和气泡出现时间延后;完全流化速度下,通过上升、合并长大、破裂过程,在分布板位置形成气泡;通过钛渣固体矢量图得出,整个床层以气泡为分界,气泡上升对上、下部颗粒的流动产生影响,导致床层不均匀.
关键词:
四氯化钛
,
高钛渣
,
氯化
,
流化床
,
数值模拟
,
流动特性
覃悦
,
文鹤鸣
,
何涛
复合材料学报
doi:10.3321/j.issn:1000-3851.2007.02.023
研究了卵形弹丸撞击下FRP层合板的侵彻和穿透性能,在局部化破坏模式假定的基础上改进了Wen提出的能量简化分析模型.改进模型仍假设弹体在侵彻过程中表面所受靶体的平均压力由靶体材料弹塑性变形所引起的静态阻力和速度效应引起的动阻力两部分组成,认为侵彻过程中靶体对弹的阻力不再是一个常数,而是与侵彻速度相关的函数.同时针对不同厚度靶板的破坏模式,建立了几种不同的侵彻和穿透模型.通过弹头长度与靶板厚度的比较,将侵彻过程分为部分侵彻和完全侵彻;穿透过程分为薄板穿透和中厚板穿透.并且根据不同的破坏方式给出了求解卵形弹丸的侵彻深度、残余速度和极限速度的预测公式.模型预测与实验数据进行了比较,发现侵彻深度和弹道极限速度的理论预测值与实验数据吻合得很好.
关键词:
FRP层合板
,
侵彻
,
穿透
,
弹道极限
,
卵形弹丸
