WU Sheng-li
,
FU Chang-liang
,
LIU Cheng-song
,
XU Jian
,
KOU Ming-yin
钢铁研究学报(英文版)
The mathematical model of minimum safety factor that investigated the collapse trends of coke layer under different charging parameters was established firstly on the basis of the slope stabilization theory in soil mechanics, and then the model of burden profile after coke collapse was improved by adopting the predetermination of quadratic curve and energy correction methods. The research will provide theoretical evidences for describing the coke profile more accurately and technical direction for choosing suitable charging parameters of blast furnace. The results show that: it is helpful to improve the stability of coke layer with increasing chute inclining angle and length of the coke flat; when the main falling point of ore moves toward furnace wall or the coke flat is wider, the curve radian of burden profile after coke collapse becomes smaller; the ore to coke ratio distribution agrees with the gas top temperature measurement well under considering coke collapse comparing with the result of ignoring coke collapse.
关键词:
blast furnace
,
coke layer stability
,
safety factor
,
coke collapse
,
burden profile
WU Sheng-li
,
LIU Cheng-song
,
FU Chang-liang
,
XU Jian
,
KOU Ming-yin
钢铁研究学报(英文版)
On the basis of the existing originally modified calculation models of theoretical combustion temperature (TCT), some factors, such as the combustion ratio of pulverized coal injection (PCI), the decomposition heat of PCI and the heat consumption of SiO2 in ash reduced in high temperature environment, were amended and improved to put forward a more comprehensive model for calculating TCT. The influences of each improvement on TCT were studied and the results were analyzed compared with those of traditional model and originally modified model, which showed that the present model could reflect the thermal state of a hearth more effectively.
关键词:
blast furnace
,
theoretical combustion temperature
,
improved calculation model
Dauter Oliveira
,
WU Sheng-li
,
DAI Yu-ming
,
XU Jian
,
CHEN Hong
钢铁研究学报(英文版)
In order to obtain good sintering performance, it is important to understand sintering properties of iron ores. Sintering properties including chemical composition, granulation and high-temperature behaviors of ores from China, Brazil and Australia. Furthermore, several indices were defined to evaluate sintering properties of iron ores. The results show that: for chemical composition, Brazilian ores present high TFe, low SiO2, and low Al2O3 content. For granulation, particle diameter ratio of Brazilian ores are high; particle intermediate fraction of Chinese concentrates are low; and average particle size and clay type index of Australian ores are high. For high-temperature properties, ores from China, Brazil and Australia present different characteristics. Ores from different origins should be mixed together to obtain good high-temperature properties. According to the analysis of each ore′s sintering properties, an ore blending scheme (Chinese concentrates 20%+Brazilian ores 40%+Australian ores 40%) was suggested. Moreover, sinter pot test using blending mix was performed, and the results indicated that the ore blending scheme led to good sintering performance and sinter quality.
关键词:
sintering
,
iron ore
,
sintering property indices
,
ore blending scheme
CAO Yong-guo
,
WU Sheng-li
,
HAN Hong-liang
,
WANG Hong-wei
,
XUE Fang
,
LIU Xiao-qin
钢铁研究学报(英文版)
Pilbara blending iron ore powder (PB powder) is blending ores with good and poor quality iron ores, so how to use PB power effectively is a problem. The self-characteristics of PB powder and its single-components were studied respectively, such as the macroscopic properties, microscopic properties, and high-temperature properties; the behavior and effect in the sintering were mastered. Then based on the new ore-proportioning idea of iron ores sintering characteristics complementary, the principles on the effective use of PB powder were discussed, and was further validated through the sintering pot test and industrial production. The results show that: PB powder is composed of three kinds of iron ore, and the sintering characteristics of different iron ores are obviously discrepant. With the ore-proportioning optimization based on the iron ores sintering characteristics complementary, the proportion of PB iron ore powder can be increased to more than 45%.
关键词:
Pilbara blending ore
,
sintering
,
mixed state
,
high effective utilization
WU Sheng-li
,
LIU Xiao-qin
,
ZHOU Qi
,
XU Jian
,
LIU Cheng-song
钢铁研究学报(英文版)
The reduction degradation characteristics of typical sinter, pellet and lump ore were tested with the reducing gas conditions simulating two kinds of iron-making processes. The results show that, in the same condition of gas composition and temperature, the reduction degradation degree (RDI＜3.15 mm) of sinter is high, RDI＜3.15 mm of lump ore is low and RDI＜3.15 mm of pellet is in the middle level. With two kinds of gas composition simulating different iron-making processes, the reduction degradation indices (RDI) of three kinds of iron ores all present the tendency of “inverted V-shape” in the temperature range from 450 to 650 ℃, and the RDI reach the maximum value at 550 ℃. The reduction degradation degrees of iron ores are extended when mixing the gas with hydrogen to increase the reduction potential, and the influence extent is discrepant for different iron ores. Colligating the increase amplitude of grains in small size fraction, the influence of reducing gas on lump ore is the greatest, the influence on sinter is the second, and the sensitivity of pellet on the reducing gas properties change is relatively small. As for the degradation form, lump ore and sinter both present the degradation of cracking, and the distribution of small grains generated from the cracking is in the range from 0.5 to 6.3 mm uniformly. The lump ore presents surface cracking, while sinter presents integral cracking. The pellet presents the degradation of surface stripping, and the proportion of grains smaller than 0.5 mm is the highest, which is up to 90% in the grains smaller than 3.15 mm.
关键词:
sinter
,
pellet
,
lump ore
,
low temperature reduction degradation characteristic
,
gas property
李铂
,
周建江
,
夏伟杰
,
吴连慧
液晶与显示
doi:10.3788/YJYXS20142904.0605
直线是机载座舱显示画面中最基本的图元,其显示质量对于整个画面的显示效果影响较大,尤其是小角度下直线显示的“麻花”现象一直是影响显示效果的关键问题之一.为了提高小角度下直线的显示效果,本文提出了一种基于Wu算法的亮度渐变改进算法.该算法通过渐进地展现直线从轴方向上的亮度变化过程,减少亮度畸变,有效地改进了显示效果.通过Matlab仿真和FPGA实现,验证了该算法反走样后的小角度直线显示效果明显优于其他算法,而且结合中点画线法后,绘制时间与Wu算法相当.同时该算法还可改善大角度直线和圆弧的显示效果,消除了大角度直线的边缘锯齿,解决了圆弧在小角度部分的虚化问题.因此本文算法可用于对实时性和显示效果要求高的机载座舱显示系统,以缓解飞行员的视觉疲劳.
关键词:
座舱显示
,
反走样
,
改进Wu算法
,
小角度
,
FPGA实现
吴连慧
,
周建江
,
夏伟杰
,
陈雅雯
液晶与显示
doi:10.3788/YJYXS20153001.0163
对于光栅化的三角形,其边缘存在明显的锯齿现象,因此需要进行反走样处理.基于Wu直线反走样算法的思想,考虑了水平直线外侧直接添加插值点的算法和三角形三边外侧反走样的算法.综合两者的优点,在绘制光栅化的三角形的同时,边缘叠加Wu反走样直线,并考虑背景像素灰度值的作用.结果表明,改进的三角形光栅化的边缘反走样算法有效提高了三角形光栅化后边缘的显示效果,该算法计算量小,便于FPGA实现,可用于对图形显示质量要求很高的机载显示系统.
关键词:
反走样
,
Wu算法
,
光栅化
,
FPGA
胡跃鑫
,
冯玉林
,
姜伟
应用化学
doi:10.3724/SP.J.1095.2011.00521
采用不同尺寸的碳酸钙粒子增韧高密度聚乙烯,研究了不同温度下共混体系的临界粒子间距与碳酸钙粒子尺寸和含量之间的关系,确定了温度是Wu氏增韧理论临界粒子间判据适用性的重要影响因素.结果表明,在17℃下,临界粒子间距与碳酸钙粒子的尺寸和含量无关,该条件下Wu氏增韧理论临界粒子间距判据是适用的;而随着温度的升高,发现临界粒子间距依赖于碳酸钙粒子的尺寸,表明高温条件下,Wu氏增韧理论临界粒子间距判据不再适用.
关键词:
聚合物增韧
,
粒子间距
,
脆韧转变
李志宏
,
柳卫平
,
白希祥
,
郭冰
,
连钢
,
颜胜权
,
王宝祥
,
陆昀
,
曾晟
,
苏俊
原子核物理评论
doi:10.3969/j.issn.1007-4627.2005.01.006
利用8Li次级束测量了质心系能量7.8 MeV 2H(8Li, 9Li)1H反应的角分布, 导出了8Li(d, p)9Li反应的天体物理S因子及9Li→8Li+n虚衰变的渐近归一化系数.
关键词:
8Li(d,p)9Li反应
,
角分布
,
天体物理S因子
,
渐近归一化系数
