WU Wei
,
WU Wei
,
HU Yanbin
,
LIU Liu
,
DING Yongliang
钢铁研究学报(英文版)
The contrast experiment of different stirring modes, which includes a new type of stirringinjection with the method of pulse and rotation, and the initial oneway stirring method, is done through physical simulation in the laboratory. The stirring methods of pulse and rotation are of two kinds. One is pulsed and rotary stirrer with positive and opposite directions. The other is pulsed and rotary stirrer with rotationstoprotation. The results show that the stirring mode of pulse and rotation has better effects than the oneway stirring method. The specific effects are that the mixing time of the melting bath is apparently shortened, the number of grains involved in the liquid surface is increased, and the residence time of air bubble in water is doubled.
关键词:
hot metal;desulphurization;injection;physical simulation;pulse;rotation
WU Wei
,
YANG Libin
,
ZHENG Congjie
,
LIU Liu
钢铁研究学报(英文版)
By measuring the mass transfer coefficient of between water and oil, the oxygen transfer rate of bath in the BOF smelting process is researched, and the influence of top and bottom blowing gas flow rate on the mechanism of mass transfer between metal and slag is discussed. The results show that when the bottom blowing gas flow rate increases on the conditions of top blowing, the mass transfer rate evidently increases, and the influence ratio of top blowing on the mass transfer is 10 percent of bottom blowing; The relation among top gas flow rate, bottom gas flow rate and lance height are established by the stirring power density. The equation between the mass transfer coefficient between metal and slag is formed, which furnishes reference for optimizing process parameters of BOF. The relation between the emulsification ratio between water and oil and the bottom blowing gas flow rate on the condition of top and bottom blowing is obtained. The result shows that with the increase of the bottom blowing gas flow rate the emulsification ratio increases in linearity, which increases the mass transfer rate of benzoic acid between water and oil.
关键词:
the oxygen transfer rate;metal and slag reaction;cold simulation;the stirring power density
WU Wei
,
MENG Hua-dong
,
LIU Liu
,
YUAN Tian-xiang
,
BAI Yan-jiang
,
YAN Zhan-hui
钢铁研究学报(英文版)
The slag melting characteristic of slag forming and slag splashing for 300 t BOF less slag process is researched by combining the methods of the slag chemical composition, the melting point determination and the petrographic analysis. The results show that the melting point of final slag for less slag smelting is 20 ℃ lower than that for conventional smelting. According to results of the petrographic analysis, the C3S (3CaO·SiO2) and C2S (2CaO·SiO2) content for less slag smelting are lower than those for conventional smelting, while the RO (FeO, MgO, MnO, etc) phase and C4AF (4CaO·Al2O3·Fe2O3) phase are higher than those for conventional smelting. According to results of the chemical analysis, the (CaO) content and slag basicity for less slag smelting are higher than those for conventional smelting, while (FeO) and (MgO) content in slag for less slag smelting are almost equal to those for conventional smelting. The reason why slag melting point for less slag smelting is lower than that for conventional smelting is that the quantity of added fluorite for less slag smelting is more than that for conventional smelting. According to the analysis results the slag melting point is determined by the C3S, C2S, RO phase and C4AF content. According to the results of slag melting characteristic before and after slag splashing for less slag smelting, the present adjusting slag process has little effect. It is important to adjust the composition of BOF final slag. The (FeO) content in slag is to be reduced at the slag splashing and adjusting slag process for less slag smelting.
关键词:
less slag smelting
,
melting point determination
,
petrographic analysis
,
slag forming process
,
slag splashing
WU Wei
,
LIU Yue
,
LIU Liu
,
XUE Zhengliang
钢铁研究学报(英文版)
On the basis of the thermodynamic analysis and fundamental study in the laboratory, the equilibrium of the TiAlO system was investigated. The results showed that the equilibrium titanium content in the steel increased with the increase in the soluble aluminum content in the steel and the TiO2 content in the slag. Although the slag basicity decreased and Al2O3 content in the slag increased, the titanium content increased. Based on these results, the BOF smelting process of low titanium bearing steel was put forward.
关键词:
bearing steel;titanium content;experiment
LIU Yue
,
WU Wei
,
LIU Liu
,
LIU Ming
,
LI Yangzhou
钢铁研究学报(英文版)
When titanium element appears in bearing steel, it is very easy to create titanium nitride inclusion, which reduces the fatigue life of bearing steel. Based on the production data of bearing steel produced by BOF, it is found that the titanium takes its source in bearing steel; the factors affecting titanium content, and the thermodynamics behavior of titanium under smelting condition were studied. The results show that the prime reasons of titanium content increment are the soluble aluminum content and the titanium oxide of slag. The comparison between the experimental data and theoretical ones shows that there is a big declination when the soluble aluminum content of steel is higher, which is caused by the nonequilibrium reaction of slag and steel. The apparent equilibrium distribution coefficient of titanium between slag and steel is obtained by use of experimental data.
关键词:
BOF;bearing steel;titanium;thermodynamics;apparent equilibrium distribution coefficient
李铂
,
周建江
,
夏伟杰
,
吴连慧
液晶与显示
doi:10.3788/YJYXS20142904.0605
直线是机载座舱显示画面中最基本的图元,其显示质量对于整个画面的显示效果影响较大,尤其是小角度下直线显示的“麻花”现象一直是影响显示效果的关键问题之一.为了提高小角度下直线的显示效果,本文提出了一种基于Wu算法的亮度渐变改进算法.该算法通过渐进地展现直线从轴方向上的亮度变化过程,减少亮度畸变,有效地改进了显示效果.通过Matlab仿真和FPGA实现,验证了该算法反走样后的小角度直线显示效果明显优于其他算法,而且结合中点画线法后,绘制时间与Wu算法相当.同时该算法还可改善大角度直线和圆弧的显示效果,消除了大角度直线的边缘锯齿,解决了圆弧在小角度部分的虚化问题.因此本文算法可用于对实时性和显示效果要求高的机载座舱显示系统,以缓解飞行员的视觉疲劳.
关键词:
座舱显示
,
反走样
,
改进Wu算法
,
小角度
,
FPGA实现
吴连慧
,
周建江
,
夏伟杰
,
陈雅雯
液晶与显示
doi:10.3788/YJYXS20153001.0163
对于光栅化的三角形,其边缘存在明显的锯齿现象,因此需要进行反走样处理.基于Wu直线反走样算法的思想,考虑了水平直线外侧直接添加插值点的算法和三角形三边外侧反走样的算法.综合两者的优点,在绘制光栅化的三角形的同时,边缘叠加Wu反走样直线,并考虑背景像素灰度值的作用.结果表明,改进的三角形光栅化的边缘反走样算法有效提高了三角形光栅化后边缘的显示效果,该算法计算量小,便于FPGA实现,可用于对图形显示质量要求很高的机载显示系统.
关键词:
反走样
,
Wu算法
,
光栅化
,
FPGA
胡跃鑫
,
冯玉林
,
姜伟
应用化学
doi:10.3724/SP.J.1095.2011.00521
采用不同尺寸的碳酸钙粒子增韧高密度聚乙烯,研究了不同温度下共混体系的临界粒子间距与碳酸钙粒子尺寸和含量之间的关系,确定了温度是Wu氏增韧理论临界粒子间判据适用性的重要影响因素.结果表明,在17℃下,临界粒子间距与碳酸钙粒子的尺寸和含量无关,该条件下Wu氏增韧理论临界粒子间距判据是适用的;而随着温度的升高,发现临界粒子间距依赖于碳酸钙粒子的尺寸,表明高温条件下,Wu氏增韧理论临界粒子间距判据不再适用.
关键词:
聚合物增韧
,
粒子间距
,
脆韧转变
