LONG Xiao
,
HE Sheng-ping
,
XU Jian-fei
,
HUO Xu-ling
,
WANG Qian
钢铁研究学报(英文版)
In high speed continuous casting of peritectic steel slabs, mold fluxes with high basicity are required for less surface defect product. However, the basicity of remaining liquid slag film tends to decrease in casting process because of the crystallization of 3CaO·2SiO2·CaF2. Thus, a way is put forward to improve mold fluxes′ properties by raising the original basicity. In order to confirm the possibility of this method, the effect of rising original basicity on the properties of mold fluxes is discussed. Properties of high fluorine based mold fluxes with different basicities and contents of CaF2, Na2O, and MgO were measured, respectively. Then, properties of higher basicity mold fluxes were discussed and compared with traditional ones. The results show that increasing the basicity index can improve the melting and flow property of mold fluxes. With the increasing basicity, crystallization rate of mold fluxes increases obviously and crystallization temperature tends to decrease when the basicity exceeds 1.35. The method presented before is proved as a potential way to resolve the contradiction between horizontal heat transfer controlling and solidified shell lubricating for peritectic steel slab casting. But further study on improving the flow property of liquid slag is needed. This work can be used to guide mold fluxes design for high speed continuous casting of peritectic steel slabs.
关键词:
mold flux
,
high basicity
,
crystallization property
,
peritectic steel
F.T.Cheng
材料科学技术（英文）
The present communication addresses an interesting problem related to the indeterminacy in hardness of superelastic NiTi reported by Xu et al. The origin of the indeterminacy is attributed to the inadequacy of the conventional Vickers hardness testing measurement which does not record elastic deformation, and thus the indeterminacy may be removed with suitable techniques. Concepts of hardness in relation to deformation are clarified. Recommendations for measuring the hardness of NiTi and other elastic-plastic materials are suggested, together with comments on the advantages and disadvantages of each of these methods.
关键词:
Hardness
,
null
,
null
,
null
,
null
,
null
Jingpei XIE
,
Yaomin ZHU
,
Xiaoping WANG
材料科学技术（英文）
The M-s temperature, Delta G(gamma-->alpha), Delta G(gamma-->M) and mechanical energy under a non-severe impact loading in a medium manganese steel (Fe-7Mn-1.2C) have been calculated by means of Xu's Fe-X-C model. The relation between the yield strength of austenite and the driving force for martensite transformation has been established. It is proved that the martensite transformation can take place in a medium manganese steel (Fe-7Mn-1.2C alloy) under a non-severe impact loading.
关键词:
李莉
,
李庆芬
,
郑磊
,
徐庭栋
,
杜善义
钢铁研究学报
以工业用12Cr1MoV钢为研究对象,通过俄歇电子能谱分析方法(AES),对磷在恒温过程中的非平衡晶界偏聚浓度进行了测定.获得的磷在钢中的非平衡晶界偏聚动力学曲线直接验证了非平衡晶界偏聚动力学理论中的Xu-Song模型.
关键词:
晶界偏聚
,
临界时间
,
扩散
,
钢
徐菊良
,
邓博
,
孙涛
,
李劲
,
蒋益明
金属学报
doi:10.3724/SP.J.1037.2009.00598
利用Thermo-Calc软件并结合金相显微镜,定性研究了2205双相不锈钢在800℃下敏化不同时间后的微观组织演变过程.通过研究扫描速率、介质成分、介质温度和试样表面状态优化了双环电化学动电位再活化法(DL-EPR),并用该优化方法研究了2205双相不锈钢晶间腐蚀敏感性.结果表明:DL-EPR法能定量评价σ相对2205双相不锈钢晶间腐蚀敏感性的影响,随敏化时间延长,σ相含量增多,晶jian 腐蚀敏感性也随之增加.腐蚀形貌的观测验证了这一规律,
关键词:
2205双相不锈钢
,
DL-EPR
,
晶间腐蚀敏感性
,
σ相
Haihua LIU
金属学报(英文版)
doi:10.1016/S1006-7191(08)60120-9
A novel method was reported to measure the remnant magnetic field in Lorentz mode in a FEI Tecnai F20 transmission electron microscope equipped with a Lorentz lens. The movement of the circle Bloch line of the cross-tie wall in Permalloy is used to measure the remnant magnetic field by tilting the specimen and adjusting the objective lens current. The remnant magnetic field is estimated to be about 17 Oe, in a direction opposite to that of the objective lens magnetic field. The remnant magnetic field can be compensated by adjusting the value of the objective lens current.
关键词:
Lorentz electron microscopy
,
Lorentz lens
,
remnant magnetic field
,
Permalloy
,
cross-tie walls
