Nuclear Engineering and Design
Liquid droplet erosion (LDE), which often occurs in bellows made of nickel-based alloys, threatens the security operation of the nuclear power plant. As the candidate materials of the bellows, Inconel 600 and Inconel 625 were both tested for resistance to cavitation erosion (CE) and jet impingement erosion (JIE) through vibratory cavitation equipment and a jet apparatus for erosion-corrosion. Cumulative mass loss vs. exposure time was used to evaluate the erosion rate of the two alloys. The surface and cross-sectional morphologies before and after the erosion tests were observed by scanning electron microscopy (SEM), the inclusions were analyzed by an energy dispersive spectroscopy (EDS), and the surface roughness was also measured by surface roughness tester to illustrate the evolution of erosion process. The results show that the cumulative mass loss of CE of Inconel 625 is about 1/6 that of Inconel 600 and the CE incubation period of the Inconel 625 is 4 times as long as that of the Inconel 600. The micro-morphology evolution of CE process illustrates that the twinning and hardness of the Inconel 625 plays a significant role in CE. In addition, the cumulative mass loss of JIE of Inconel 625 is about 2/3 that of Inconel 600 at impacting angle of 90 degrees, and almost equal to that of the Inconel 600 at impacting angle of 30 degrees. Overall, the resistance to CE and JIE of Inconel 625 is much superior to that of Inconel 600. (C) 2010 Elsevier By. All rights reserved.
关键词:
stress-corrosion cracking;aluminide intermetallic alloys;high-purity;water;mechanical-properties;crevice corrosion;solid particles;wear;behavior;microstructure;deformation;steam
Nuclear Engineering and Design
A composite coating was deposited on Inconel 600 substrate by cold spray method using pure Ni powder (60 wt.%) blended with alpha-Al(2)O(3) (40 wt.%) as feedstock. It is expected to be applied to repair the bellows eroded by the liquid droplet erosion (LDE). Microstructure of the coating was observed using optical microscope (OM) and scanning electron microscopy (SEM). Microhardness of the coating was determined by Vickers hardness tester. Cavitation erosion (CE) experiments were carried out in the distilled water. Jet impingement erosion (JIE) experiments were performed in slurry containing 1 wt.% quartz particle with the flow velocity of 15 m/s at impingement angles of 30 degrees, 60 degrees and 90 degrees, respectively. Cumulative mass loss vs. testing time was used to evaluate the erosion rate of the coating. The erosion mechanism was analyzed by OM, SEM, X-ray diffraction (XRD) and the microhardness measurement. The results show that the composite coating has compact microstructure and relatively high hardness. The resistance to CE of the coating is not as good as that of Inconel 600 substrate due to the weak bonds of the Al(2)O(3) particles. However, the results of the JIE test indicate that the slurry erosion resistance of the coating is better than that of Inconel 600 at the impact angles of 30 degrees and 60 degrees, but not at the normal impact angle. (C) 2011 Elsevier B.V. All rights reserved.
关键词:
large powder particles;composite coatings;slurry erosion;kinetic;spray;liquid impact;alloy;microstructure;steels;deposition;resistance
徐卫兵
,
戈明亮
,
何平笙
应用化学
doi:10.3969/j.issn.1000-0518.2001.09.011
用熔融插层法制备聚甲醛/蒙脱土纳米复合材料,用X射线衍射研究聚甲醛及复合材料的微观结构,表明复合材料是纳米复合材料.用DSC法研究其非等温结晶行为,对所得数据分别用Jeziorny法、Ozawa法和Liu法进行处理.结果表明,Jeziorny法和Liu法处理非等温结晶过程比较理想.聚甲醛及聚甲醛/有机蒙脱土纳米复合材料的结晶活化能分别为334.6和196.9 kJ/mol,说明有机蒙脱土的加入,降低了聚甲醛的结晶活化能,且t1/z缩短,起到了异相成核的作用.
关键词:
聚甲醛
,
蒙脱土
,
纳米复合材料
,
非等温结晶动力学
王平华
,
徐国永
应用化学
doi:10.3969/j.issn.1000-0518.2004.08.007
用熔融复合法制备聚丙烯/凹凸棒土纳米复合材料,用DSC法研究其非等温结晶行为,对所得的数据分别用Jeziorny法、Ozawa法和Liu法进行处理.结果表明,Jeziorny法和Liu法处理非等温结晶过程比较理想.聚丙烯及聚丙烯/凹凸棒土纳米复合材料的结晶活化能分别为194.1和162.8 kJ/mol,表明凹凸棒土的加入,降低了聚丙烯的结晶活化能,且t1/2缩短,起到了异相成核作用.
关键词:
聚丙烯
,
凹凸棒土
,
纳米复合材料
,
非等温结晶动力学
Scripta Materialia
A recent comment on a previously published paper addressed the invalid explanation of the off diagonal interdiflusion coefficients of the beta-Ni(Al,Cr) phase in the Ni-Cr-Al system according to the symmetric property of the thermodynamic matrix. In this paper, the experimental data presented by Hou et al. was reanalyzed and the interdiffusion coefficient matrix was estimated again. The results of the analysis have been discussed in terms of a brief reply to the comments of Liu and Liang. (C) 2010 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.
关键词:
Diffusion;Intermetallic compound;Ni-Cr-Al
邓超
,
邵玮
,
李春忠
高分子材料科学与工程
采用元机纳米锑掺杂二氧化锡(ATO)和有机聚醚酯(PEE)协同提高聚时苯二甲酸乙二酯(PET)的抗静电性能,合成了聚对苯二甲酸乙二酯-聚醚酯/锑掺杂二氧化锡纳米复合材料(PET-PEE/ATO).使用Czawa方程和Liu-Mo方程研究了PET-PEE/ATO纳米复合材料的非等温结晶过程.Ozawa方程研究发现,在非等温结晶过程中,PET、PET-PEE、PET/ATO、PET-PEE/ATO的成核性能依次提高.Liu-Mo方程发现,ATO和PEE的加入分别促进了异相成核作用和加快了结晶生长,PET-PEE/ATO结晶成核性能最好,结晶速率最快.
关键词:
聚对苯二甲酸乙二酯
,
有机聚醚酯
,
无机纳米锑掺杂二氧化锡
,
纳米复合材料
,
非等温结晶动力学
