常永勤
,
介万奇
,
郭喜平
,
陈福义
,
安卫军
功能材料
研究了ACRT-B法生长的Mn0.1Cd0.9In2Te4晶体中界面的形状和各组元沿轴向的分布规律及其分凝因数.发现结晶界面为椭球形;采用理想配比生长MnxCd1-xIn2Te4晶体,其4种组元并不按(Mn,Cd):In:Te=1:2:4比例结晶,而是要重新分布;通过数学方法处理实验数据得到Mn,Cd和In的分凝因数在α相区分别为1.286、1.9257和0.7294,在β相区则分别为1.12、1.055和0.985.
关键词:
ACRT-B法
,
MnxCd1-x In2Te4
,
界面
,
分凝因数
常永勤
,
安卫军
,
郭喜平
,
介万奇
无机材料学报
采用Bridgman法生长了x为0.1,0.22和0.4的四元稀磁半导体化合物MnxCd1-xIn2Te4晶体.研究了三根晶体中相的形貌、结构、成分和Mn0.1Cd0.9In2Te4晶体中各组元沿轴向和径向的成分分布.晶体生长初始端的组织为α+β+β1,随着生长的进行,形成β相的单相区.在晶锭末端,形成In2Te3类面心立方结构化合物.组分x增大后,MnxCd1-xIn2Te4晶体的吸收边向短波方向移动,禁带宽度则线性增大.磁化率测量结果表明:晶体在高温区的x-1-T曲线服从居里-外斯定律,在低温区(<50K)则表现出顺磁增强现象.
关键词:
MnxCd1-xIn2Te4
,
compositional distribution
,
infrared transmission spectra
,
mag- netic susceptibility
常永勤
,
安卫军
,
郭喜平
,
介万奇
无机材料学报
doi:10.3321/j.issn:1000-324X.2003.02.004
采用Bridgman法生长了x为0.1,0.22和0.4的四元稀磁半导体化合物MnxCd1-xIn2Te4晶体.研究了三根晶体中相的形貌、结构、成分和Mno.1Cd0.9In2Te4晶体中各组元沿轴向和径向的成分分布.晶体生长初始端的组织为α+β+β1,随着生长的进行,形成β相的单相区.在晶锭末端,形成In2Te3类面心立方结构化合物.组分x增大后,MnxCd1-xIn2Te4晶体的吸收边向短波方向移动,禁带宽度则线性增大.磁化率测量结果表明:晶体在高温区的x-1-T曲线服从居里一外斯定律,在低温区(＜50K)则表现出顺磁增强现象.
关键词:
MnxCd1-xIn2Te4
,
成分偏析
,
红外透射光谱
,
磁化率
常永勤
,
安卫军
,
郭喜平
,
介万奇
功能材料
采用Bridgman法生长四元稀磁化合物半导体Mn0.22Cd0.78In2Te4晶体.当晶体生长到预定长度时,淬火得到固液界面.采用光学显微镜、扫描电镜、X射线衍射仪、ISIS能谱仪以及Leica定量金相分析仪研究了晶体中出现的界面形态、相的形貌和数量以及沿生长方向的相析出规律,并进行了相成分分析.研究发现,淬火得到的Mn0.22 Cd0.78In2Te4晶体中存在两个界面,其中一个为固液相变界面,另一个为由α+β两相区发展到单相β区时的转变界面,二者相对于生长初始端均为凹形;α+β两相区中,β相以条状、花状和近似圆片状形式存在,其中条状β相多分布在晶界处;越接近生长初始端,花状和近似圆片状β相越小,条状β相越细,它们的含量越少;X射线衍射图谱表明,β相为黄铜矿结构,α相为面心立方结构.
关键词:
MnxCd1-xIn2Te4
,
相变界面
,
β相
,
X射线衍射图谱
Acta Materialia
A graded microstructure was produced in the surface layer of a pure Cu sample by means of surface mechanical attrition treatment (SMAT) [Wang K, Tao NR, Liu G, Lu J, Lu K. Acta Mater 2006;54:5281.]. The diffusion behavior of (63)Ni in such a surface layer was investigated by the radiotracer technique at temperatures <438 K. It is shown that the effective diffusivity in the top 10 mu m surface layer is more than 2 orders of magnitude higher than that along conventional high-angle grain boundaries (HAGB) in Cu of similar purity. The diffusion rate increases gradually with increasing depth up to 30-50 mu m, and then decreases with further increasing depth. The enhanced diffusivities reveal higher-energy states of various interfaces in the SMAT surface layer. The excess free energy of HAGB in this layer is estimated to be similar to 30% higher than that of conventional grain boundaries. An apparent retardation of the effective diffusion rate in the top 25 mu m surface layer is induced by tracer leakage into numerous twin-boundary-like interfaces, while the gradual decrease in interface excess free energy correlates with the observed decrease in diffusivity in the subsurface layer at depths exceeding 50 mu m. (C) 2009 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.
关键词:
Nanostructured material;Surface mechanical attrition treatment;Diffusion;Grain boundaries;Twin boundaries;grain-boundary diffusion;mechanical attrition treatment;severe;plastic-deformation;nanocrystalline copper;self-diffusion;nickel;alloys;bulk;temperatures;segregation
刘守平
,
周上祺
,
王佳眉
,
任勤
腐蚀学报（英文）
用金相显微镜、扫描电镜、X射线衍射仪和X射线能谱仪对天然气井油管悬挂器腐蚀失效进行了检测分析，并对天然气井油管悬挂器用35CrMo钢进行了盐雾试验，结果表明，天然气中的水和CO2是引起腐蚀的主要介质，腐蚀产物主要是FeCO3，高速天然气冲刷和钢中的非金属夹杂加剧了腐蚀的速度.
CORROSION FAILURE ANALYSIS OF AN OIL TUBE USED IN NATURAL GAS WELL
LIU Shou-ping,ZHOU Shang-qi,WANG Jia-mei,REN Qin
Chongqing University
A failed oil tube used in natural gas well was examined by optical microscope,scanning electron microscope ,X-ray diffractometer and X-ray spectrometer.Corrosion behavior of 35CrMo steel samples of the oil tube were investigated by means of salt spray tests in the laboratory.The results show that CO2 and H2O are primary factors in the corrosion of oil tube.The corrosion product is FeCO3,non-metallic inclusions in the steel and erosion of natural gas fluid played an important role in accelerating the corrosion.
oil tube;
natural gas well；
35CrMo steel；
failure analysis；
corrosion
关键词:
悬挂器
,
null
,
null
,
null
Journal of Materials Research
The morphology of the dark and bright regions observed by transmission electron microscopy for the Zr(64.13)Cu(15.75)Ni(10.12)Al(10) bulk metallic glass strongly depends on the ion beam parameters used for ion milling. This indicates that the ion beam could introduce surface fluctuation to metallic glasses during ion milling.
关键词:
room-temperature
