材料期刊网

Ultrasonic Analysis of Cracking Propagation Morphology in the Fusion Zone of High Strength Steel

Yajiang LI , Zengda ZOU , Dezhen LIU , Huiqiang WU , Juan WANG

材料科学技术（英文）

Cracking morphology in the fusion zone of HQ130 high strength steel was researched by "the y-silt test" and "three point bend test", ultrasonic test and microscope. HQ130+QJ63 high strength steel was welded by Ar+CO2 gas shielded arc welding under the condition of no-preheat. Experimental results indicated that welding crack produced in the partially melted zone of the weld root of HQ130 steel side and propagated parallel to the fusion zone. The cracking developed alternatively between the weld and the partially melted zone, and is not strictly to rupture at W/F boundary surface. Controlling weld heat input (E) about 16 kJ/cm could make the cracking rate to be lowest and satisfy the performance requirement of welded joint zone.

关键词: High strength steel , null , null

Microstructure and Fracture Morphology in the Welding Zone of T91 Heat-resisting Steel Used in Power Station

Yajiang LI , Bing ZHOU , Tao FENG , Jiangwei REN

材料科学技术（英文）

Microstructure performance in the welding zone of T91 heat-resistant steel under the condition of TIG welding was researched by means of metallography, X-ray diffraction and scanning electron microscope (SEM).Experimental results indicated that microstructure of T91 weld metal was austenite + a little amount of d ferrite when using TGS-9cb filler wire.Substructure inside the austenite grain was crypto-crystal lath martensite, on which some Cr23C6 blocky carbides were distributed. The maximum hardness (HRC44) in the welding zone is near the fusion zone. There existed no obvious softening zone in the heat-affected zone (HAZ). For T91 steel tube of F63 mm×5 mm, when increasing welding heat input (E) from 4.8 kJ/cm to 12.5 kJ/cm, fracture morphology in the fusion zone and the HAZ changed from dimple fracture into quasi-cleavage fracture (QC). Controlling the welding heat input of about 9.8 kJ/cm is suitable in the welding of T91 heat-resistant steel.

关键词: T91 heat-resistant steel , null , null

Microstructure and Fracture Morphology in the Welding Zone of Cr18Mo2 Ferritic Stainless Steel

Yajiang LI , Zengda ZOU and M. Thompson (Dept. of Materials Engineering , Shandong University of Technology , Jinan 250061 , China)(To whom correspondence should be addressed)

材料科学技术（英文）

Microstructure, precipitates and fracture morphology in the weld metal and the heat-affected zone (HAZ) of Cr18Mo2 ferritic stainless steel have been studied by means of metalloscope, SEM,TEM and X-ray diffractometer. Experimental results indicate that crystalline grain coarsening in HAZ is one of the reason resulting in the embrittlement fracture in the welding zone of the ferritic stainless steel. Some precipitates (TiC, TiN and Cr2N) in the steel promote production and development of the brittle cracks. In practical applications. the welding heat input should be as small as possible to prevent embrittlement caused by HAZ grain coarsening.

关键词:

Microstructure in the weld metal of austenitic-pearlitic dissimilar steels and diffusion of element in the fusion zone

Yajiang LI , Zengda ZOU , Bing ZHOU

材料科学技术（英文）

Microstructure and alloy element distribution in the welded joint between austenitic stainless steel (1Cr18Ni9Ti) and pearlitic heat-resistant steel (1Cr5Mo) were researched by means of light microscopy, scanning electron microscopy (SEM) and electron probe microanalysis (EPMA). Microstructure, divisions of the fusion zone and elemental diffusion distributions in the welded joints were investigated. Furthermore, solidification microstructure and S-ferrite distribution in the weld metal of these steels are also discussed.

关键词:

ON SPINODAL BOUNDARIES OF Al-Li ALLOYS

WEI Yinghui , WANG Xiaotian (School of Materials Scince and Engineering , Xi'an Jiaotong University , Xi'an 710049 , China Manuscript received 10 Mareh , 1994)

金属学报(英文版)

The spinodal decomposition can occur in Al-Li alloys containing 5.8-14.2 at.% Li at room temperature. The modutated structure wavelength is approximately 3.1 nm for com mercial Al-LI alloys. The limit composition of the miscibility gap is 3.66 -16.06 at.%Li at 298 K. The highest temperature of the miscibility gap is 377 K.

关键词: : Al-Li alloy , null , null

大爆炸核合成相关的8Li(d, p)9Li反应截面测量

李志宏 , 柳卫平 , 白希祥 , 郭冰 , 连钢 , 颜胜权 , 王宝祥 , 陆昀 , 曾晟 , 苏俊

原子核物理评论 doi:10.3969/j.issn.1007-4627.2005.01.006

利用8Li次级束测量了质心系能量7.8 MeV 2H(8Li, 9Li)1H反应的角分布, 导出了8Li(d, p)9Li反应的天体物理S因子及9Li→8Li+n虚衰变的渐近归一化系数.

关键词: 8Li(d,p)9Li反应 , 角分布 , 天体物理S因子 , 渐近归一化系数

CRYSTAL STRUCTURE OF γ-Li_xFe_2O_3 WITH ELECTROCHEMICAL INSERTION OF Li

HUANG Jianshun CHEN Junming Shanghai Institute of Metallurgy , Academia Sinica , Shanghai , China Research Associate , Shanghai Institute of Metallurgy , Academia Sinica , Shanghai 200050 , China

金属学报(英文版)

Crystal structure of γ-Li_xFe_2O_3,inserted Li electrochemically,was studied by Moss- bauer spectroscopy together with X-ray diffraction,XPS and electrochemical method,On the insertion of Li at low current density,the crystal structure is keeping original spinel; while at higher current density or by thermal activation,owing to violent movement of Li~+ ions,part of crystal structure transforms into rock type similar to face-centered cubic structure of ferrous oxide.The transition channels during insertion of Li~+ ions and limitation of Li~+ ions inserted were discussed.

关键词: null , null , null

Al—Li合金的晶界断裂

姚大平 , 张匀 , 胡壮麒 , 李依依

材料研究学报

本文研究了两种晶粒组织的二元Al-Li 合金拉伸性能与断裂行为。结果表明Al-Li 合金力学性能与晶粒尺寸有关,其断裂行为决定于PFZ 内平面滑移或晶界沉淀相与滑移的交互作用。

关键词: Al—Li合金 , intergranular fracture , planar slip

Effect of Li(3)N additive on the hydrogen storage properties of Li-Mg-N-H system

Journal of Materials Research

The effect of Li(3)N additive on the Li-Mg-N-H system was examined with respect to the reversible dehydrogenation performance. Screening Study with varying Li(3)N additions (5, 10, 20, and 30 mol%) demonstrates that all are effective for improving the hydrogen desorption capacity. Optimally, incorporation of 10 mol% Li(3)N improves the practical capacity from 3.9 wt% to approximately 4.7 wt% hydrogen at 200 degrees C, which drives the dehydrogenation reaction toward completion. Moreover, the capacity enhancement persists well over 10 de-/rehydrogenation cycles. Systematic x-ray diffraction examinations indicate that Li(3)N additive transforms into LiNH(2) and LiH phases and remains during hydrogen cycling. Combined structure/property investigations suggest that the LiNH(2) "seeding" should be responsible for the capacity enhancement, which reduces the kinetic barrier associated with the nucleation of intermediate LiNH(2). In addition, the concurrent incorporation of LiH is effective for mitigating the ammonia release.

关键词: complex hydrides;improvement;mixtures;imides;amide;h-2

SUPERPLASTICITY OF A RAPIDLY SOLIDIFIED AI-Li ALLOY

MANG Weishi WANG Guozhi ZHANG Yongchang HU Zhuangqi SHI Changxu Institute of Metal Research , Academia Sinica , Shenyang , China Yongchang Associate Professor , Institute of Metal Research , Academia Sinica , Shenyang 110015 , China

金属学报(英文版)

A rapidly solidified microcrystalline Al-Li-Cu-Mg-Zr alloy and its superplasicity have been investigated.An optimum tensile elongation of 585% was obtained at 540℃ and strain rate 1.67×10~(-2)s~(-1).The superplastic Al-Li alloy is manufaetured using thermomechanical pro- cessing:solution,overaging,warm rolling and recrystallization.Microstructural changes in thermomechanical processing and cavitation occurred during superplastic deformation have been observed.The superplastic failure of alloy may be caused mainly by nucleation and growth of cavities as well as the linkage around grains.

关键词: superplasticity , null , null , null