中国腐蚀与防护学报
N。1Atmospheric Corrosivlty for Steels………………………………………………… .LIANG Caideng HO[I i。-tat（6）Caustic Stress Corrosion Cr。king of Alloy 800 Part 2.The Effect of Thiosul执e……………………………………… KONG De-sheng YANG Wu ZHAO Guo-zheng HUANG De.ltL。ZHANG Yu。。he CHEN She。g-bac（13）SERS slid E16CttOCh6iniC81 Stlldy Of Illhibit1Oli M6ch＆tllsth Of ThlollY68 Oil ITOll ID H....
关键词:
Nuclear Instruments & Methods in Physics Research Section B-Beam Interactions with Materials and Atoms
A static Monte Carlo simulation program has been used to study the influence of primary and secondary knock-on atoms on the angular distribution and the fractionation, for zero-fluence sputtering of Mo-92-Mo-100. At 10 keV Xe ion energy, calculations show that significant depth-dependent momentum asymmetry exists in the near-surface region, as in Refs. (L.P. Zheng, R.S. Li, M.Y.LI, Nucl. Instr, and Meth. B 100 (1995) 490; L.P. Zheng, M.Y. Li, Nucl. Instr. and Meth. B 114(1996) 28). The calculations also show that at the polar emission angle range between 0 degrees and 90 degrees the probabilities of the sputtered primary knock-on atoms for Mo-92 and Mo-100 are small (6.1% for Mo-92 and 6.6% for Mo-100), especially, between 0 degrees and 30 degrees they are very small (2.5% for Mo-92 and 2.8% for Mo-100). At 0.1 keV Ar ion energy, the calculations show that partial momentum flux ratios, for the primary and the secondary knock-on atoms, deviate far from one, through marker plane 1 (about an atomic layer distance from the surface). (C) 1998 Elsevier Science B.V. All rights reserved.
关键词:
mo-92-mo-100;targets
李红
,
孙克
,
李艳萍
,
石毅
,
郭金花
,
卢志超
金属功能材料
提出了采用推杆式热膨胀仪测试非晶合金薄带热膨胀特性的新方法.分析了Fe80Si9B11非晶薄带的热膨胀曲特性和非晶合金晶化过程.根据R.G.Zheng理论分析了结构弛豫中自由体积比变化,发现自由体积比曲线出现双峰.结合晶化前发生相分离的理论分析了这种变化的原因.分析表明:铁基非晶Fe80Si9B11晶化过程中先形成α-Fe(Si)相,再析出Fe3B、二次α-Fe(Si)相.晶化前先发生相分离,自由体积比增大,然后析出结晶相α-Fe(Si),自由体积比降低.随温度升高,B偏聚,自由体积比增大,随后析出Fe3B、二次α-Fe(Si)相,自由体积比降低.
关键词:
铁基非晶薄带
,
热膨胀系数
,
自由体积比
,
结构弛豫
李凤娟
,
吕国光
金属世界
doi:10.3969/j.issn.1000-6826.2014.04.14
通过对烧结配料所需原料及对冷烧结矿成品检验采制样方法的分析，找出影响检验结果真实性的因素，采取有效的改进措施，使本钢原料厂一次配料、本钢炼铁厂265 m2烧结二次配料及265 m2烧结系统各项稳定率有了很大的提高，烧结矿实物质量和各项技术质量指标有了很大的进步，保证了高炉的稳定顺行。
提高本钢265 m2冷烧结矿及原料检验代表性的实践
Practice of Improving the 265 m2 Cold Sinter and Raw Material Inspection Representative
供稿|
李凤娟,吕国光/
LI Feng-juan, LV Guo-guang
DOI：10.3969/j.issn.1000-6826.2014.04.14
导读内容
本钢炼铁厂265 m2烧结机生产所需要的含铁原料比较复杂，一次配料料种较多，且烧结含铁原料是由本钢原料厂二车间供料，原料质量的不稳定，会影响烧结矿质量的提高和新一号高炉的强化及高炉技术指标的改善。本钢质量管理中心驻冷烧检查站加强了对烧结配料所需原料及对冷烧结矿成品检验采制样代表性的研究，采取了一些改进措施，达到了良好的效果。含铁料成分稳定率、烧结矿各项质量和技术指标在稳步地提高。下面，对本钢质量管理中心驻冷烧检查站就提高采样及检验过程的准确性所采取的措施和办法进行说明。
烧结矿采样是半自动采样，每两小时采样一次，作为一个批次，来代表整个2h烧结矿的成份。
关键词:
