S.C. Fan 1)
,
X.H. Wang 2)
,
J.J. Zhang 2) and J.M. Wan 2) 1)School of Mechanical Engineering
,
Tianjin University
,
Tianjin 300070
,
China 2)School of Mechanical Engineering
,
Hebei University of Technology
,
Tianjin 300130
,
China
金属学报(英文版)
Plasma spraying technics, a method of strengthening surfaces, shows advantages in wear-resistant, reducing friction, bearing corrosion and enduring higher temperature. While for the coating material, it is important to improve the ability of the functional coating. In this paper, a coating material of wear-resistant, bearing corrosion and enduring higher temperature in middle and low speed diesel is studied quantificationally with a uniform prescription design method, which reduced the test period as the test points distribute uniformly. An optimized combination is put forward of each part in the coating and a method to develop a new coating material is supplied.
关键词:
coating
,
null
,
null
,
null
D.Q.Tang
,
Y. Wang
,
E.Y.Jiang
,
C.Zhao and F.L.Sun Department of Applied Physics
,
Tianjin University
,
Tianjin 300072
,
China
金属学报(英文版)
CN x films were made by a facing targets sputtering ( FTS) systemon the Si(100) substrate under different N 2 partial pressure. XRD, XPS, FTIR and Raman Spectroscopy( RS) were measured to investigate the structure and the binding state of the film. The films are amorphous and the N/C increases with the N 2 partial pressure increasing and reaches 0 46 when the N 2 pressure is 100%. The N incorporated C forms N sp 2C and N sp 3C mainly and there is a small amount of C≡N.
关键词:
H. Y. Jing
,
L. X. Huo
,
Y. F. Zhang and F. Minami( 1) College of Material Science
,
Tianjin University
,
Tianjin 300072
,
China 2) Osaka University
,
Japan)
金属学报(英文版)
A computation framework for brittle fracture which incorporates weakest link statistics and a microme- chanics model reflecting reflecting local damage of the material is described.The Weibull stress W emerges as a probabilistic fracture parameter to define the condition leading material failure. Unstable crack propa- gation occurs at a critical value of W which may be attained paior to or following some amount of duc- tile crack extension. A realistic model of ductile crack growth using the computation cell methodology is used to define the evolution of near tip stress fields during crack extension. An application of proposed framework to predict the measured geometry and ductile tearing effects on the statistical distributio of fracture toughness for the pipe line steel welded joint is described.
关键词:
fracture toughness
,
null
,
null
X. Q. Yang
,
L. X. Huo
,
Y. F. Zhang and J. X. Yan (School of Material Science and Engineering
,
Tianjin University
,
Tianjin 300072
,
China)
金属学报(英文版)
The buckling formation and influence factors during welding thin - plated structures were investigated based on finite element methods, An engineering treatment method for prdicating the buckling distor- tion was proposed in here. It was used the equivalent applied thermal - load to simulate the welding residual stress,therefore the calculation of complex welding distoriton can be transformed into 3D elas- tic structural applied- load analyses, which can reduce the quantities of calculating works effectively. The validation of the method was verified by comparison of the numerical simulation and experimental results. The simulation of buckling distorition for side - walled structrues of paseenger train was per- formed and the calculation was in agreement with measuring results in general. It was shown that the main factors for producing the buckling were the intermittent fillet and ping the during welding the stiffened beams and columns to the panel.The existence of the free edge of panels would reduce the crit- ical buckling stress and enlarge the deflection obviously,but the continuous weld in closed frames didn' t degrade the buckling situation.
关键词:
welding buckling distortion
,
null
,
null
