J. T. Niu
,
Y. H. Tian
,
B. Y. Li
,
J. J. Xu
,
L.M. Liu (National Key Laboratory of Advanced welding Production Technology
,
HIT
,
Harbin 150001
,
China)
金属学报(英文版)
Tensile strength of diffusion welded joint of aluminum matrix composite is very low due to its poor weld- ability.In this paper, solution and age treatments were conducted on the welded joint of Al2O3p/ 6061Al composite subjected to diffusion welding using Gleeble 1500 machine, and ensile strengt...
关键词:
aluminum matrix composite
,
null
,
null
J. T. Niu
,
L. M. Liu
,
J. P. Zhai
,
J. Yu
,
X. M. Zhang (National Key Laboratory of Advanced Welding Production Technology
,
HIT
,
Harbin 750001
,
China)
金属学报(英文版)
Effects of diffusion welding parameters on strength of welded joint based on particle reinforced alumini- um matrix composite Al2O3p/6061Al were studied by comparing with aluminium matrix alloy,Mecha- nism for the loss of joint strength was analyzed.It was pointed out that the key processi...
关键词:
particle reinforced aluminium matrix composite
,
null
,
null
梁方
,
竺培显
,
周生刚
,
马会宇
材料热处理学报
采用扩散焊接法制备出了Ph-Sn-Al复合电极材料。借助线形扫描伏安法(LSV)、SEM测试手段研究了不同工艺参数对Ph-Al复合材料界面及电化学性能的影响。结果表明,在230℃、2h或1h下扩散焊接条件下,得到了界面冶金式结合的Pb-Al复合材料;与液固包覆法制备的电极材料相比,界面结合明显改善;...
关键词:
Ph-Al复合电极材料
,
扩散焊接法
,
界面演变
,
电化学性能
潘厚宏
,
刘拥军
,
张大向
,
伊藤勲
机械工程材料
在1.3Pa的真空环境下,用扩散焊接法进行了Cu-x%Bi合金(x=0,0.5,1.0,2.0)与ZrO2陶瓷的连接,并采用扫描电镜、电子探针及剪切试验机等研究了铜铋合金与ZrO2陶瓷扩散焊接头的组织及剪切强度。结果表明:在焊接压力作用下挤入接合界面的铋,在焊接后部分残留在界面上,对焊接热应力有缓释...
关键词:
扩散焊
,
铜铋合金
,
ZrO2陶瓷
,
剪切强度
张建
,
罗国强
,
李美娟
,
王仪宇
,
沈强
,
张联盟
材料科学与工艺
采用扩散焊接方法对钼铜异种材料进行了焊接,研究了直接焊接和加镍作为中间层焊接对焊接接头界面显微组织的影响,通过SEM、EDS、EPMA、XRD等测试方法对其显微结构进行了表征.结果表明,直接焊接时,焊接界面结合紧密,Mo、Cu原子之间相互扩散形成扩散层,接头断裂发生在扩散层,由于柯肯达尔效应作用,在...
关键词:
扩散焊接
,
钼与铜
,
显微组织
,
Ni中间层
邵甄胰
,
陈天赐
,
宋庭丰
,
蒋小松
,
朱德贵
材料热处理学报
doi:10.13289/j.issn.1009-6264.2016-X291
利用真空扩散焊接方法,研究了不同保温时间对不锈钢和钛合金焊接接头组织与性能的影响.结果表明,不锈钢与钛合金在900℃下直接进行扩散焊接,难以得到较好的性能.随保温时间延长接头强度逐渐降低,在保温120 min时得到最高屈服强度为43.01MPa.焊缝界面处主要形成α-Ti、β-Ti、FeTi、Fe2...
关键词:
异种金属焊接
,
不锈钢
,
钛合金
,
扩散焊接